For the truss loaded as shown determine the forces in members FH, GH, and GI in kilonewtons. Use the method of sections. (Due to the nature of this problem, do not use rounded intermediate values in your calculations 3.0 kN 1.6 kN A В 2.5 m 8.8 kN 3.6 kN D 2.5m 3.6 kN V F 2.5m 3.6 kN V H 2.5m 1.6 kN V 2.5 m 2.5m

For the truss loaded as shown determine the forces in members FH, GH, and GI in kilonewtons. Use the method of sections. (Due to the nature of this problem, do not use rounded intermediate values in your calculations 3.0 kN 1.6 kN A В 2.5 m 8.8 kN 3.6 kN D 2.5m 3.6 kN V F 2.5m 3.6 kN V H 2.5m 1.6 kN V 2.5 m 2.5m

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Calculate the force in member 12. Note: Given end of the question 12 is not the grade. You have to calculate force in member 1-2
A simply supported beam AB is loaded as shown in the figure. CDE is a rigid member.Draw SFD
Determine the maximum tensile or compressive stresses in the beam due to bending. The section has a base b= 140 mm and h= 240 mm PLACE THE ENTIRE PROCEDURE
Find shear and bending diagram, and of this structure. deflection El k K₁ rigid rigid W
Completely solve. WRITE LEGIBLY OR TYPEWRITE THE SOLUTIONS. BOX THE FINAL ANSWER.
12 - In the plane truss system, the loading status of which is evident in the figure, the support reactions and all rod forces will be found. A is the fixed joint and B is the sliding joint. Single upload P = 35 kN, dimensions a = 1 m and bar numbers are given. Based on this, which of the following is true? A) The S2 bar is the draw bar.B) NoneC) S3 and S4 bar are pressure bars.D) S1 and S2 bars are pressure bars.E) The S4 bar is the draw bar.
Given: Consider the truss shown below and the series of loading. 20 k Required: 8⁹ An 8⁹ 8⁹ 8' 8' a 10 k 8' (A) (A) Calculate the force in member bd for case (A) (B) Calculate the force in member bd for case (B) (C) Calculate the force in member bd using the principle of superposition for the truss loading below. DO NOT use equilibrium equations. 10 k d 5 k a 8⁹ 8' (B) b 8'
The cantilever beam consists of a rectangular structural steel tube shape [E = 29,000 ksi; I = 1570 in.“]. For the loading shown, determine: (a) the beam deflection at point A. (b) the beam deflection at point B. Assume MA = 160 kip-ft, P = 10 kips, LAB = 9.0 ft, LBC = 13.5 ft. MA A В C LAB LBC Answer: (a) VA = in. (b) Ув in.
The steel truss is shown in the figure. Indicate in your solution, whether the member undergoes tension (T) or compression (C). 15 KN B F 10m D f5m4 A 10m 10m ILI E 40 KN C 5m. GO- 4m 6m 10m Determine the axial force in member DA in KN.0 Determine the axial force in member AC in KN.0 Determine the axial force in member DF in KN.0
H.W. 1:An axial member consisting of two polymer bars is sup- ported at C, as shown in Figure area ol 540 mm and an elastic modulus of 28 GPa. Bar (2) has a cross-sectional area of 880 mm2 and an elastic modulus of 16.5 GPa. Determine the deflection of point A relative to support C. . Bar (1) has a cross-sectional 50 kN Om She 35 kN (1) (2) 50 kN 0.85 m 1.15 m FIGURE
Upvote will be give. Please write the complete solutions and FBD. Use 2 decimal places.
X Your answer is incorrect. The simply supported beam consists of a W21 x 44 structural steel wide-flange shape [E = 29,000 ksi; I = 843 in.“]. Assume that the support at D can provide resistance %3D either up or down. For a loading of w = 5.4 kips/ft, determine: (a) the beam deflection vg at point A. (b) the beam deflection vc at point C. Assume LAB = 13 ft, LBc = 7 ft, LcD =7 ft, LDE = 6 ft. %3D A B E LAB LBC LcD LCD Lpe Answers: (a) VA = -0.65669 in. (b) vc = 0.024937 in.