For the truss and loading shown, determine most economical cross-sectional area (in in2) of member EG, if P = 26006 lb, Q = 34853 lb, y = 7.26 ft, and the stress in the member is 20.96 ksi . Round off the final answer to four decimal places. For the truss and loading shown, determine most economical cross-sectional area (in in2) of member EG, if P = 26006 Ib, Q = 34853Ib, y = 7.26 ft, and the stress in the member is 20.96 ksi . Round off the final answer to four decimal places.0004(1).png...ВDFHyCEG4 panels at 10 ft = 40 ft

Answered: Image /qna-images/answer/2f412ee7-3f73-4b3a-b4bd-19366b6c2673.jpg

Answered: For the truss and loading shown,…

For the truss and loading shown, determine most economical cross-sectional area (in in2) of member EG, if P = 26006 lb, Q = 34853 lb, y = 7.26 ft, and the stress in the member is 20.96 ksi .

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Give me right solution
Q1/ Member B is subjected to a compressive force of 10 kips. If A and B are both 0.5 in. thick and made of a material with the shear stress-strain diagram shown below. Determine the smallest dimension a in order to prevent shear failure. Use a factor of safety of F.S. = 5.0 £s. Th (ksi) A y (rad) 90- 80 70 60 50 40 30 20 10 Ofpl = 0.008 Y = 0.54 0.73
Answer the problem question and store value and then use 4 decimal places as final answer then box the final answer. Don’t forget the unit. Take note: Write it on a paper, hand written showing correct answer.
#1 will upvote anyone who will answer
A
20. A steel section is subjected to a combination of shear and bending actions. The applied shear force is V and the shear capacity of the section is Vs. For such a section, high shear force (as per IS: 800-2007) is defined as A. V> 0.6 Vs B. V> 0.7 Vs C. V> 0.8 Vs D. V> 0.9 Vs
PC =? PI=12+00.00 T = ? E = ? L = ? Tangent, T = Degree, Da= Length, L = Long Chord, LC = MO = ? LC = ? R = 5730 ft I = 1°00'00" PT=? Questions 29-34: Calculate the remaining parts of the circular curve given above: External, E = Middle Ordinate, MO =
20. A steel section is subjected to a combination of shear and bending actions. The applied shear force is V and the shear capacity of the section is Vs. For such a section, high shear force (as per IS: 800-2007) is defined as A. V> 0.6 Vs B. V> 0.7 Vs C. V> 0.8 Vs D. V> 0.9 Vs
Determine the member stresses in members AB, AC, AD, BC, and BD if the cross-sectional area for all members is 800 mm². Note: You may use any method 3 m ון 2 - 3 m 4 m 5 m 6 kN Situation 4: Terminologies 1. A structural element that carries a load that is applied transverse (perpendicular) to its length and the top fibers are in compression; the bottom fibers are in tension. 2. A structural element that is composed of smaller structural members typically configured in triangular arrangements. 3. Codes that specify combinations of loads that must be considered in the design of structures in the Philippines? 4. How many equations of equilibrium are there in space structures? 5. These are the forces exerted by supports on the structure and tend to prevent its motion and keep it in equilibrium. 6. The internal force in the direction of or parallel to the centroidal axis of the beam 7. The internal force in the direction perpendicular to the centroidal axis
Solve the following problems completely and neatly. Use 3 decimal places in all your computations except for strain and rho(5 decimal places). Input your answer in the text box provided in each number. Calculate the stress in the steel of the section in PART B in MPa.0
For the cross-section shown below, determine the maximum amount of tension reinforcement (A.) so that the beam cross-section is tension-controlled. [hint: use the strain diagram shown below]. Use fy = 60 ksi and fe=4 ksi. b=12 in. E, = 0.003 †d'= 2.5 in A' =2#9 n.a. d=17.5 in A = ? E, = 0.005