For the system shown in the figure:1) Find the response in steady state when a force is applied at point Af(t) = Feiwt and at point B a movement is imposed y(t) = Yeiwt2) Calculate the amplitude of the displacements of the block for m=1, c=1, k=1, F=10,Y=5, w=5, expressed in coherent units.y(1)<+BỊ++x(1)Akkf(t)M

Answered: Image /qna-images/answer/cbf1eacc-a94d-4406-ab58-d5212ff26c28.jpg

For the system shown in the figure: 1) Find the response in steady state when a force is applied at pointA f(t) = Feiwt and at point B a movement is imposed y(t) = Ye*wt 2) Calculate the amplitude of the displacements of the block for m=1, c=1, k=1, F=10, Y=5, w=5, expressed in coherent units.

For the system shown in the figure: 1) Find the response in steady state when a force is applied at pointA f(t) = Feiwt and at point B a movement is imposed y(t) = Ye*wt 2) Calculate the amplitude of the displacements of the block for m=1, c=1, k=1, F=10, Y=5, w=5, expressed in coherent units.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

5
6. Determine the response of a system with a degree of freedom to an F impulse for the following data: m = 3kg, c = 5 Ns/m, k = 17 N/m, F = 6. The answer has the format below: x(t) = Xe wnt sen(wat) Determine the value of amplitude X.
Q2\\ For the System shown in figure determine 1. Equation of Motion 2. Find the response of the system, as the initial condition is (X = 2 cm at the block). Note: m= 1kg. M 3 kg, c= S0 N-s/m, k-200 N/m, and r- 10 cm. and determine the response after 10 sec. 2r Activate
I will rate the solution if done correctly and neatly
Question (2). The following system has a block of a mass m = xykg(from your registration mUrnber), stiffness k= 12000 N/m, damping coefficient c = xy• 10 kg/s, base motion y(t)= 0.01 sin(3t), calculate the following: %3D 1 Natural frequency. 2 Base frequency. 3. Steady-state part of the response X(t) k y(1) base wW
42. k= 1080N/m wwwwww 30 kg X = Ae 5.₂ ( F = 25cos wt (N) (a) A 30kg cart is acted upon by the harmonic force shown in the figure. If c = 0, determine the range of the driving frequency w for which the magnitude of the steady state response is less than 75mm Ans: [w 6.86rad/s] (b) If the driving frequency for the system is a = rad/s, determine the required value of the damping coefficient, C, if the steady state amplitude is not to exceed 75mm. Ans: [55.6 Ns/m²]
Consider the two-mass system shown below. The system is free to move in the x₁ - x₂ plane. 1. Obtain the FBD 2. Obtain the EOM 3. Using Modal Analysis, obtain the response of the system x2 X4 3k 4k 4k quing m m=10kg, k = 100 N/m m k 2k m 4k
Suppose a spring mass damper system with k=4000N/m, m=10kg,and c=40N-s/m Find the steady-state and total response of the system under harmonic force F(t)=200 cos t N and the initial conditions x0=0.1m and ̇x0'=0
Consider a system whose model is given by m dx²(t) dt² +c dx(t) dt -+kx(t)=5, where m = 1, c = 5, and k = 10. Which of the following statement(s) is (are) true? Select all that apply. The homogeneous solution has the form of x(t) =C₁e - t - t n This is a critically damped system. This is an over-damped system. This is a unstable system. This is a under-damped system. This is an asymptotically stable system. The homogeneous solution has the form of x(t) =e -500 1 n (C₁cosa +C₂sina}). The homogeneous solution has the form of x(t) = C₁e³¹² + C₂e²²
Consider a dynamic system that consists of a block, a pulley, a spring, and a damper shown in Figure 1. The moment of inertia of the pulley around its rotation center is 6mr² and the mass of the block is m. The left end of the damper is moving horizontally with the displacement y = Y sin wt. Find the amplitude of the steady state motion of the block. y=Ysin wt k m Figure 1: