For the state of stress shown, determine the value of Txy for which the maximum shearing stress is 82 MPa. (Round the final answer to two decimal places.) 70 MPa The value of Txy is ± 78.10 t 120 MPa MPa.

Q: 5. वि० D 10' F is the orange arrow C 10' B 45* 1000lbs Find FAD, FBC, FCD FAB FAC TH

A:

Q: i cant read this.. can you write it out??

A:

Q: 3. During tug of war, the bicep muscle generated 4k N force that was perpendicular to the forearm…

A:

Q: Suppose that A24 . Eaun) • Part C Determine the coordinate direction angie of the resutant force of…

A:

Q: Which of the following statement is correct O 1. Reynolds number depends on the viscosity of fluid O…

A:

Q: * Which of the following is used to ? measure the discharge pilot tube O current meter none of the…

A:

Q: I o2s+lo4 s+1. .96 2. L'st ++T?

A:

Q: 600 N/m 2 m 4 m R2 R1

A: Consider upward force as (+)ve and downward force as (-)ve. Assume clockwise moment as (+)ve and…

Q: 6. From among the following, the largest increment of pressure is A. 1 Pa B1 psi C. 1 in H₂O D. 1 in…

A:

Q: QUESTION 8 What is the specific volume of air at 184 K and 139.23 kPa? Give your answer in mkg to 3…

A: Solution is attached below:

Q: Given data : Work done-3800 J

A: Given data : Force=F Work done=W   To find : Displacement

Q: Please show detailed solution in a handwritten format. Don't use chatgpt. Torque and Maximum shear…

A: Step 1: Step 2: Step 3: Step 4:

Q: 1. What do you mean by measurement? Why it is needed?

A:

Q: Where can i get the values: x2=0.92 and v2 = 13.5079

A:

Q: Early showerheads consumed either 5 or 7 gallons of water per minute (gpm). Federal plumbing…

A:

Q: Please help. Written on paper not typed on computer or keyboard please. Need help on all questions.…

A:

Q: What are the units of F in the equation below: F = mg/gc where m is mass in lbm; g is acceleration…

A: Given;m is the mass in lbm (pounds mass).g is the acceleration due to gravity, which is given as…

Q: I needed it to be solved using differential equation

A:

Q: In a steady flow through a nozzle, the flow velocity on the nozzle axis is given by v-uo (1+3x/L)i…

A:

Q: Ideal and real gases are described below. Select a correct description. O a. For a fixed amount of…

A: Ideal gas  Gasses that elastically collide amongst their molecules and that do not have…

Q: Given: Diameter of pipe in point 1 = 3.2 Diameter of pipe in point 2 = 2.3 Specific gravity of the…

A: since the units of pressure are not provided, assuming the unit to be ft of water Velocity at…

Q: The bore diameter of each cylinder in a six-cylinder four-stroke petrol engine is 25 mm and the…

A:

Q: Read the questions again. Your answer is not what I'm asking. Please redo it.  where is my FBD. Can…

A: The free-body diagram of the smaller cart is shown below.The free-body diagram of the larger cart is…

Q: The magnitude of the buoyant force is proportional to the volume of fluid displaced by the object.…

A: 1. False  2. True  3. False  4. False

Q: 3. A pump discharges 126 liters per second of brine (sp.gr.1.20). The pump inlet, 304.8 mm diameter,…

A: Given: The volume flow rate of brine, Q = 126 liters/s = 0.126 m^3/s The specific gravity of brine,…

Q: Shape factor S=M/N, N isShape factor S=M/N, N is

A: Shape factor defines the ratio of the under which two surfaces project over one another.

Q: A15 A16 A17 A loss of head due to sudden contraction is known as minor head loss. TRUE The pressure…

A: Note: Since you have posted a question with multiple sub-parts, we will solve first three sub- parts…

Q: Question2-1 Thermal hot wire anemometers measure the temperature of the flow, and they are very…

A: answer 2-1 False : Anemometers are used for measuring  speed and direction of wind

Q: Compute the thickness of the web, t, of the channel shape section

A:

Q: 500N 100N 300mm 800 N 900 N 28°

A:

Q: Please help. Written on paper not typed on computer or keyboard please. Need help on both…

A: Approach to solving the question: Detailed explanation:Examples: Key references:

Q: Please correctly answer all parts of the question. Thank you will upvote if correct!

A: (2) The Pirani gauge is a robust thermal conductivity gauge used for the measurement of pressures in…

Q: True Story! The 1998-1999 Mars Climate Orbiter mission was declared a total loss in 1999 as there…

A: The actual distance of orbiter from surface is .The distance taken of orbiter taken for calculation…

Q: Deleimine wasik done

A: Given data : The value of force applied=F The value of displacement=D   To find : Work done

Q: 1. Energy consumption in a country from 2001 to 2011 increased from 1041.3 million to 1526.1 million…

A: The measurement for doing work is known as energy. Electrical energy is defines as a movement of…

Q: find the diameter of cylinder, specific weight is=25 N/m^3, Mass=2.2lbs, Acceleration=32.2m/s^2,…

A: Given :-  Specific weight = 25 N/m2 Mass (m) = 2.2 lb = 0.997903 kg Height of the cylinder (h) = 1 m…

Q: 1.5 mm + 2.0 mm 2.0 mm 3.0 mm A shear force, S, is applied. This results in shear flow, shown with…

A: Shear flow at a junction is analogous to current at a junction. That is, the total amount of shear…

Q: Fluid viscosity is the proportionality constant between the shear force and the change of fluid…

A: True

Q: ADVANCED CHEMISTRY! RATE WILL BE GIVEN! PLEASE WRITE THE COMPLETE SOLUTIONS A Steam at 400 deg C an…

A: Given:P1=8200 KPaT1=400 deg CP2=10 KPaη=0.76

Q: Which of the following statement is correct   1. Reynolds number depends on the viscosity of fluid…

A: Option 1 is correct.

Q: Diogrum height, cm The bore diameter of each cylinder in a six-cylinder four-stroke petrol engine is…

A: Given  No of cylinder K=6 4 stroke engine,

Q: 1. What are the properties of natural gas? 2. Outline the difference between non associate and…

A: (1)

Stress transformation

The term stress indicates the measure of internal forces that develop due to an external force's application on an object. When a specific external force is applied to an object, internal stress generates in the material. The value of stress can obtain by taking the ratio of the externally applied force and cross-sectional area of the object. There are different types of stress depending on the type of external force.