For the spring device shown, the spring constant is 2 N/cm and the undeformed length is 20 cm. If the spring is pushed back 10 cm and the 0.3-N ball is shot from rest, determine the velocity when the ball is leaving the ejection chute. Neglect the mass of the spring.

For the spring device shown, the spring constant is 2 N/cm and the undeformed length is 20 cm. If the spring is pushed back 10 cm and the 0.3-N ball is shot from rest, determine the velocity when the ball is leaving the ejection chute. Neglect the mass of the spring.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A 2 kg ring is attached to a spring of 3 m length that is not elongated. The ring is immobile from point B If it is released from the state, determine its velocity when it reaches point A.
The initially stationary 11-kg block is subjected to the time-varying force whose magnitude Pis shown in the plot. The 26° angle remains constant. Determine the block speed at (a) t = 3.2 s and (b) t = 6.4 s. 76 11 kg 26 SH=0.44 %3D (H = 0.37 7.7 I, s Answers: (a) At t = 3.2 s, v= i m/s (b) At t = 6.4 s, v= m/s
5
The second stage of a two-stage rocket weighs 2000 lb (empty) and is launched from the first stage with a velocity of 3000 mi/h. The fuel in the second stage weighs 1000 lb. If it is consumed at the rate of 50lb/s and ejected with a relative velocity of 8000 ft/s, determine the acceleration of the second stage just after the engine is fired. What is the rocket’s acceleration just before all the fuel is consumed? Neglect the effect of gravitation.
A car climbs through a slope of 30° in 5 seconds. If it starts at rest and after 10 m its velocity is 80 km/h. What is the power that the car has to develop? What is the force that produces this power and makes it possible for the car to climb and accelerate? Assume the car does not suffer any temperature change and that its mass is m = 450 kg. d = 10 m 0 - 30°
I need the answer as soon as possible
Please write legibly.
A motorcycle and rider have a combined mass of 350kg. The vehicle's velocity is 100 km/hr. The rider is to go up a hill incline of 10 meters. The wheels each have a mass of 20 kg and a diameter of 500mm. The wheel design consists of 6 spokes with a mass of 0.5 kg for each spoke. a. Determine the vehicle's velocity at the top of the hill, assuming it was a rolling vehicle with engine being turned off. a. Indicate the vehicle's velocity at each meter through the climb. b. Explain the transfer energy and how this affects the behaviour of the system. At another point in its journey, the motorcycle and rider travel at 80 km/h around a left-hand bend of radius 30m. Calculate: a) The angular velocity of each wheel. b) The moment of inertia of each wheel. c) The angular momentum of the wheel prior to entering the bend. d) The magnitude of the gyroscopic torque produced on the bike as the rider is driving around the bend. What is the effect and why is it important to calculate the gyroscopic…
v(3) A crate of mass m = 10 kg is "lifted" from rest by a rope with a force given by F = 75√t N. Find the speed of the box at t = 3 s and at t = 6 s. How much higher is the box, measured from its starting position, at t = 6 s? Use impulse and momentum, I guess = v(6) = y(6) m S m 8 m m F CC UBC Engineering
Small steel balls fall from rest through the opening at A at the steady rate of 3 per second. Find the vertical separation h of two consecutive balls when the lower one has dropped 2.1 meters. Neglect air resistance. Answer: h= i 3
A block with mass m=0.4kg is released from rest and slides a distance d=2.5m down a frictionless inclined plane where it strikes a spring of spring constant K=8N/m. 0 = 30° h= d sin 0 a. Find the speed of the block just before it hits the spring. b. Show that the potential energy after the strike is described by the function U(x)= 4x² -2x assuming Uo=0J c. Find the maximum compression x of the spring. d. Determine the maximum speed of the block after the collision. e. The spring was shown to be non-ideal. Is described by the function U(x)= 4x²-x³ Find the equilibrium points for the non-ideal spring. 3.
A spring with spring constant k=70 kN/m is used to stop the box of mass m with initial velocity V1= 7 m/s. The spring is initially compressed 100 mm with cables. Since the box produces a maximum compression x=60 mm in the spring. m= 60 kg. s=750mm(a) Find the kinetic coefficient of friction between the surface and the box.(b) Find the velocity of the box as it moves back from its original position.