For the simply supported steel beam (E=200 Gpa ; I=129x10^6) shown in the figure, determine the deflection at B. Assume L=4m, P=60KN, and w=40KN/m For the simply supported steel beam ( E=200GPa ;I = 129 x 106 mm4) shown in thefigure, determine the deflection at B.Assume L = 4m, P = 60 KN, and w =%3D40KN/m.L/2L/2O -8.27 mmO -10.11 mmO -6.30 mmO -7.29 mm

Answered: Image /qna-images/answer/39ecec5f-c79f-408a-81ea-496d28ebb646.jpg

Answered: For the simply supported steel beam…

For the simply supported steel beam (E=200 Gpa ; I=129x10^6) shown in the figure, determine the deflection at B. Assume L=4m, P=60KN, and w=40KN/m

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: Please answer, I'll rate. Thank you very much! Solve using virtual

Q: For the cantilever steel beam [E = 180 GPa; | = 84 × 106 mm4], use the double-integration method to…

A: To find deflection at point A

Q: The cantilever beam loaded as shown has the following properties: El = constant. Using Double…

A: Using double integration method

Q: For the cantilever steel beam [E = 200 GPa; l = 129 × 106 mm²] shown in Figure, use the double-…

Q: For the cantilever steel beam [E = 220 GPa; I = 83 x 106 mm4), use the double-integration method to…

Q: 2. A simply supported beam carries a uniformly distributed load as shown below, determine the…

Q: For the cantilever steel beam [E = 220 GPa; I = 126 × 106 mm4], use the double-integration method to…

Q: For the beam and loading shown, use discontinuity functions to compute (a) the slope of the beam at…

A: From the given beam and loading shown it is required to compute the slope of the beam at B and the…

Q: We are given the beam shown in Fig. 4. The moment of inertia of member AB is two times bigger than…

A: E = 5000 ksi = 720000.00 ksf I = 1000 in4 = 0.0482 ft4

Q: Calculate the slope and deflection at free end.

Q: For the beam and loading shown, use discontinuity functions to compute (a) the slope of the beam at…

A: Given:- Given Data:EI = 136000 kips.ft2w0=4.6kips/ft, LAB=13ft, LBC=7ft

Q: figure 1, determine the reaction at A in kN, slope of elastic curve at A in degrees, and deflection…

Q: From the given figure below find and compute the location and maximum deflection of the beam. 600…

A: Given, There are 3 figures in the question. Note: As student is not mentioned which question to…

Q: e) the value of the integration constant C2 f) the value of the integration constant C4. g) the…

A: Data given Find : (a) the value of the integration constant C2 (b) the value of the integration…

Q: A cantilever beam subjected to uniform variable load, if the beam is made of I Beam having a…

Q: For the cantilever steel beam [E = 210 GPa; I=90 × 106 mm4], use the double-integration method to…

Q: A simply supported beam with P1=52kN, P2=60 kN and w=20kN/m has the loadings shown. If the value of…

A: Answer We can calculate the deflection at point C using the Double integration method EId2ydx2=M M…

Q: b) Determine the deflection at the free end of the beam shown in figure 2b) using the conjugate beam…

Q: From the figure, the beam used has the following properties: L = 2 m, E 200 GPa and I = 200 x 10° mm…

A: a.) The expression for maximum deflection of the beam is given as…

Q: A simply supported beam carries a load as shown in the figure below. What is the value of deflection…

Q: Thumbs-up

Q: For the beam and loading shown, use discontinuity functions to compute (a) the slope of the beam at…

Q: Determine the maximum deflection of the beam shown in Figure 4. Take El is constant

A: Using the double integration method to determine the maximum deflection in the beam, in this method…

Q: 2. A simply supported beam is loaded as shown in the figure. Using Moment-Area Method determine the…

Q: A 10 m long beam has a 3 kN point load applied to the cantilever steel beam. The load is applied 4 m…

Q: x. BO L W [ ↑ ↑ VIT

A: given- a cantilever beam, carrying UDL and point load required- to determine vertical deflection at…

Q: Vertical rod CD of length L = 2 m, cross-sectional area A = 150 mm2 %3D %3D and modulus of…

Q: E = 29,000 ksi I= 20 in 150 Ib 240 lb 0.3 k/ft B A 10 ft 8 ft 10 ft

A: Given data: E=29000 ksiI=20 in4EI=29000×20=580000 K.in2EI=4027.78 k.ft2

Q: ation, determine the deflection at the free end of the beam shown 60 kN 300 kN–m 5 m 5 m L= 10 m El…

A: Consider the given figure Moment at fixed end due to point load at C MA=60×10 =600 kNm

Q: QUESTION 1 A built-in beam shown in Figure 1 carries a distributed load of 30 KN/m between point A…

Q: For the cantilever steel beam [E = 210 GPa; /= 124 × 106 mm4], use the double-integration method to…

Q: The inverted T-beam supports the loads as shown in the figure. Using E=200 GPa, a=25 mm, b=180 mm…

A: Double integration method is that it produces the equation for the deflection everywhere along the…

Q: For the cantilever steel beam [E = 300 GPa; 1= 129 x 106 mm4] shown in Figure, use the double-…

Q: An overhanging beam is loaded as shown below. Calculate the deflections under the two loads 80kN and…

A: GIVEN DATA:-⇒Overhanging beam (single side) of span = 12 m⇒Loads = point loads:-(1) 80 KN(2) 120…

Q: B 127 127

Q: Find the deflection at the midpoint BC of the loaded beam as shown in the figure by the double…

A: Given data UDL Point load Span length Simply supported beam Modulus of Elasticity Moment of…

Q: For the simply supported steel beam [E = 200 GPa; I = 129 × ] shown in figure, use the…

Q: Q3. a- A rectangular plate simply supported along its edges and subjected to a uniform of intensity…

A: "Since you have posted a question with multiple sub-parts, we will solve the first sub-part for you.…

Q: shown in the figure, a uniform load (w = 300 lb/ft) is applied on a beam (L = 8 ft) with both ends…

Q: decimal

Q: P, (kN) P₂ (kN) 1m 4.2m 1m B w (kN/m) C X D

A: Given data P1 = 76 KN, P2 = 50 KN, w = 31 KN/m, x = 3.7 m Find deflection at B in term of EI.

Q: For the beam and loading shown, use discontinuity functions to compute (a) the slope of the beam at…

A: From the given question it is required to determine the slope of the beam at B and the deflection of…

Question

100%

For the simply supported steel beam (E=200 Gpa ; I=129x10^6) shown in the figure, determine the deflection at B. Assume L=4m, P=60KN, and w=40KN/m

For the simply supported steel beam ( E=200
GPa ;I = 129 x 106 mm4) shown in the
figure, determine the deflection at B.
Assume L = 4m, P = 60 KN, and w =
%3D
40KN/m.
L/2
L/2
O -8.27 mm
O -10.11 mm
O -6.30 mm
O -7.29 mm

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Similar questions

Hw1: For the simply supported beam shown in Figure, determine the maximum deflection due to the applied load. The flexural rigidity of the beam is El= 7x106 kip.in². V₁ = 20 kips a = 12 ft 1 = 18 ft Answer: ymax = -0.129 ft downward W = 60 kips b = 6 ft 2 V₂ = 40 kips
In the structure shown, the support at A rotates 3x10-3 radians CCW, and the support at C has a settlement of 0.8 inches. Make the shear force and bending moment diagram using 1. Three-moment equation 2. Slope Deflection Method Make sure the diagrams for both methods are the same.
Use double integration method
assume that a max deflection is equal to(length/1000)mm is to be the limiting factor in selecting a W-beam having a span length of 1.47meters. Supports are at both ends and the load at the center is 24.70kN. I=71,276,243mm^4. Determine the minimum material stiffness(Young's Modulus) inGPa.
For the beam and loading shown, use discontinuity functions to compute (a) the slope of the beam at B and (b) the deflection of the beam at A. Assume a constant value of El = 107000 kip-ft² for the beam; wo = 5.0 kips/ft, LAB = 15 ft, LBc = 8 ft. Wo Xx C LAB LBC Answer: (a) 0g = (b) VA = rad in. B
Deflection is 0.196 inches explain how.
For the beam and loading shown, use discontinuity functions to compute (a) the slope of the beam at B and (b) the deflection of the beam at C. Assume a constant value of EI = 38 x 10^6 lb-ft^2 for the beam; w0 = 6800 lb/ft, LAB = 2.5 ft, LBC = 5 ft, LCD = 3 ft.
2. For the cantilever beam shown in the figure, what will cause zero deflection at A? ANS. P=112.5 N A P M = 400 N-m B 2 m 2 m
A simply supported beam is 5m long and has a fixed support at the left-hand side and a roller support at the right-hand side, 2m from the roller support the beam is subjected to a 20KN point load. Determine the slope and deflection at the point load using Direct Integration Method. Take E = 2,1x10² GPa and I = 90x100 mm¹.
Using double integration method, compute the maximum deflection for the beam loaded as shown in the figure. Usee E=10GPa and I =4.5x10^6 mm^4
A simply supported beam is subject to a downwards uniform distributed load, w, as shown below. B A uniform distributed load, w L1 L2 The cross-section of the beam is constant with second moment of area I = 3750 mm², and Young's elastic modulus is E = 200 GPa. The distributed load has magnitude w = 220 N/m. If Point B is distance L₁ (Point C), calculate: the downwards vertical deflection at Point B: C C 435 mm from the left end (Point A) and distance L2 = 385 mm from the right end Round your answer to 3 significant figures. X [Units: mm]
Give me right solution according to the question