uo 11:55A eclass.alquds.edu470% 03G JAWWAL I.For the shown sillicontransistor ofVcB=70, assume thatRcVe=10 V,RfR=4 KO,VCER=350 KO and R_= 1.2ΚΩ.%3DRETheisBQа. 12.9 Ab. 18.10 рАc. 15.5 µAd. 20.7 µAе. 10.3 рA

To find the base current for given BJT circuit

Answered: For the shown sillicon transistor of…

For the shown sillicon transistor of Vcc B=70, assume that Rc R Vcc=10 V, CC R=4 KQ, VCE R=350 KO and R̟= 1.2 RE ΚΩ. The IBo is а. 12.9 A b. 18.10 µA с. 15.5 А d. 20.7 µA е. 10.3 рА

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Determine Vx and the mode of operation of the PNP transistor shown in the figure below. Assume Is = °A, B = 50, VA = 00, and Rc = 0.1 KO. 10x10-16 %3D Vcc는 2 V 1.2 V- Rc Select one: a. 0.577 V, Active Mode O b. 0.23 V, Active Mode O c. None of these d. 1.153 V, Active Mode e. 2.306 V, Saturation Mode
Please answer quickly thank you (5)
Q7
17. A biased clamper is connected to a rectangular AC input with 20V on the positive half cycle and -10V on the negative half cycle. The orientation of the Si diode is the same with Vo while the 5V biasing voltage is in opposite connection. The value of R is 100K ohms while the capacitor is 1 microFarad.
+20 V 2 k 430 ka 10 AF I0 uF – s0 40 uF Determine the Q point and sketch the DC load line.
Determine Ic, Ig, lĘ respectively for the PNP transistor shown in the figure below. Assume Is = 5x10-15 A, B = 50, VT= 26mV, VA = ", and Rc = 0.1 KO. %3D 01 Vcc 2V 1.2 V- Rc Select one: Oa. 11.531 mA, 0.231 mA, 11.762 mA b. 5.766 mA, 0.115 mA, 5.881 mA O c 2.306 mA, 0.046 mA, 2.352 mA O d. None of these
Calculate the Resistance , if the RTD temperature is 1069.6 °C and Sensitivity is 1.5 °C/ohm O a. 9.10 O b. 1604.40 O c. 1071.10
2. A load of 8Ω is supplied by a single-switch Direct Current (DC) chopper with an inputvoltage of 40V. The switching frequency is 800Hz, the duty ratio is 0.4, and thetransmission voltage drop of the transistor is 2.4V a. Draw the chopper circuit presented in the question b. Find the switching period with the duty time of BJT c. Draw the load voltage, load current, BJT current, BJT voltage along two periods d. Find the output voltage. Is the achieved load voltage the average value or the effectivevalue e. Find the output power f. Find the average value and effective value of BJT current g. Find the power loss of BJT h. Find the DC source current i. Find the circuit efficiency
The figure below shows a three-stage circuit using two-supply emitter bias. What are the collector-to-ground voltages (VC) for each stage? Rc1 Rez Rc3 • 10 ΚΩ • 10 ΚΩ • 10 ΚΩ Vin RE1 RE2 • 20 ΚΩ • 20 ΚΩ RB₁1 · 33 ΚΩ RB2 33 ΚΩ RB3 33 ΚΩ Vcc +15 V to Yout RE3 • 20 ΚΩ VEE –15 V
For the transistor AF 114 as shown in the figure Determine the value of the collector current - 9V € 1 ΚΩ ≥ 30 ΚΩ Ic... Select one: O a. -10 mA O b. g mA c. -9 MA O d. 10 mA B E TİT
To study the input and output characteristics of a BJT in Common Emitter(CE) Configuration and plot it on graph.lab report Input Characteristics: V CE = 5V V CE = 10V V BB (volts) V BE (volts) I B (µA) V BE (volts) I B (µA) Output Characteristics: I B = 431μA (VBB=5V) I B = 930μA (VBB=10V) V CC (volts) V CE (volts) I C (mA)
The approximated peak voltage across each half of a center-tapped transformer used in full- wave rectifier that has an average output voltage of 100 V is: Select one: a. 314 V b. 157 V С. 332 V d. 253 V e. 115 V O O O O