For the shaded area, a. Locate the coordinates of the centroid. b. Calculate the moments of inertia about the given x and y axis (I, and I,).

Q: (e) Write about the difference in working principle between induced-draft counterflow and…

A: INDUCED DRAFT COUNTERFLOW COOLING TOWER NATURAL DRAFT COOLING TOWER 1. Cooling is achieved by…

Q: Using a single acting cylinder work pieces are to be fed into a jig from gravity magazine. The…

A: In this system, a single acting cylinder is used to feed work pieces into a jig from a gravity…

Q: If water has a pressure of 35 kPa absolute, at what approximate temperature will it boil?

A: This question is possible to solve with the help of steam table

Q: . Water in a hydraulic press is under a pressure of 92.580 MPa abs. at 16 degrees C. if the initial…

A:

Q: Write short note on the Difference between the PVT diagram of water and other liquids

A: Solution: To Determine: The difference between the Phase diagrams of water and other liquid.

Q: calculate the constant surface heat flux, q.".

A:

Q: 17) What is the approximate Peritectic Temperature for the system?

A: Reaction between δ + L will give peritectic reaction. Answer : 1493 deg C

Q: Why Benjamin Franklin invented the hand Boiler

A: The interaction between temperature and pressure is shown by a hand boiler. When the temperature…

Q: 8. Write down the different zones in cupola furnace.

A:

Q: Performance evaluation of centrifugal pump and sealless pump, trends, cost evaluation, and…

A: Mechanical seals are used to make seal on exit and inlet point of the roatating shaft.

Q: Problem 1 Determine the friction factor "f" for a 40 mm ID cast iron pipe handling 400 L/min of…

A:

Q: B: Drive an equation could be used to calculate liquid volumetric flow rate for rectangular open…

A: Introduction:- The volumetric flow rate is the flow of volume per unit of time. that means in a unit…

Q: 2. Comparison between; a. Bar/Rod & Beam b. Tube & Pipe

A: a) Rod & Beam Comparison 1) Rod usually has circular cross-section.  1) Beam may has different…

Q: Reaction At A &B

A: Refer attachment below

Q: Reheat cycle then solve for it

A: given; Reheat cycle then solve for it

Q: Explain the difference and/or similarities of Upfeed System and Overheadfeed System distribution of…

A: Upfeed system distribution of cold water- when water distributed directly from municipal pipe water…

Q: . Omar Juma is working in shaping machine of a gear manufacturing company. This shaping machine ram…

A: Given Data→ Shaping machine of a gear manufacturing company

Q: Water in a hydraulic press is under a pressure of 92.580 MPa abs. at 16 degrees C. if the initial…

A: Given:Final pressure in the hydraulic press, P2=92.580 MPa=92.580*106 PaInitial pressure in the…

Q: HVAC UPVOTE WILL BE GIVEN. PLEASE WRITE THE COMPLETE SOLUTIONS.  please anwer all the…

A: GivenAir is saturated Dry bulb temperature Td=22oC

Q: Consider a two-stage cascade refrigeration system operating between the pressure limits of 1.2 MPa…

A:

Q: Draw the block diagram of pressure measurement system with Analog Display.

A:

Q: describe type and properties of spring used in impact of jet apparatus.

A: Solution:

Q: I need these three parts answered pertaining to the print provided. If you can not answer all three…

A: The term, Orthogonal, describes the relationship of the axis of the ½” NPT pipe plug with the main…

Q: Fluid machinery & its application. Q-2 differential between pneumatic system and hydraulic system…

A: Need to differentiate between pneumatic system and hydraulic system.

Q: 4m colaulate the megaitude ie sraction A in kN B.

A:

Q: At the lowest points of a pipe there should be drains and while at the highest points there should…

A: The objective of the question is to understand the reason behind the placement of drains at the…

Q: Give all the parts of a simple vertical fire tube boiler

A:

Q: A piston cylinder device is fitted with stops at the top. Initially .5lbs of R-134a is in the tank…

A:

Q: 8.8. A solar collector and storage tank, shown in Fig. 8-15a, is to be optimized to achieve minimum…

A: The objective function is the total cost of the solar collector and the storage vessel. This is…

Q: Cooling system work 225 Psi intense Evaporator Pressure E

A:

Q: A punch press has punches forty (40) circles that are 2 inches in diameter through medium carbon…

A: According to given conditionwe have the following equationPunching force=Area×Pressure forceHereArea…

Q: I'm not getting the solution

A:

Q: What basic calculations would be made to verify the general problem statement: "lift cylinder…

A:

Q: Derive expressions for of mass lov rates bled steam considering

A: The answer is

Q: Derive an eeporession for Gysoscopic Couple

A: The answer is given in next step

Q: 3- List two reason, to keep low pressure drop across the production system. 5- W... a

A: Pressure drop is the most common and significant problem observed in production system. It basically…

Q: Why cascade system is the best choice for the above solution

A: A system or technique for connecting and running two induction motors so that the primary circuit…

Q: Process Flow Diagram of Mechanical Draft Cooling Tower

A: In mechanical draft cooling tower, the air is moved by power-driven fan motors to force it to go…

Q: Explain the re guage

A: solution of above problem is below:

Atomic diffusion in solids

In material science, diffusion can take place in solid, liquid, and gases. In solids, atomic diffusion can take place with the help of thermally activated and randomly vibrating atoms. The atomic diffusion in solids is complex and very slow in comparison to atomic diffusion in liquids and gases because the interatomic distance between the atoms is smaller in solids as compared to liquids and gases.