For the series/parallel pipes shown, the total head loss in the system is 25 m. Determine the flow rate in pipes 3 and 6 in L/s. AD₁ = 600 mmL₁ =1000 mn₁ = 0.011L5 =900 mD5=350 mmnç = 0.012B L3=600 mL4-750 mD3=400 mm C D4-300 mm Dng= 0.013n₁=0.011L₂ = 1500 mD₂ = 500 mmn₂ = 0.012L6 = 1200 mD6 = 500 mmn6=0.011E

Answered: For the series/parallel pipes shown,…

For the series/parallel pipes shown, the total head loss in the system is 25 m. Determine the flow rate in pipes 3 and 6 in L/s.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: 2. Consider the piping network shown. The pressure heads at points A and B are 80m and 52m,…

A: Pressure head at A, hA=80 m Pressure head at B, hB=52 m Head loss, H=80-52=28 m Hazen William…

Q: Water transfer from down reservoir to upper reservoir Water is pumped from the reservoir for…

A: Given, Flow rate, Q = 600 m3/hr or 0.167 m3/s Vapor pressure of water = 2340 Pa The pump efficiency…

Q: Pump inflow 2. Draw the HGL for the system shown below. The pump flow at A is 100 L/s with a 550 kPa…

A: Solution for this question is provided below ⬇️...Explanation:

Q: In the parallel system shown, pipe 1 has a length of 3000 ft and 20-inch in diameter. Pipe 2 is 5000…

Q: 2.) Given below are pipe lengths, sizes and connections. All pipes have a friction factor of 0.020.…

A: Given Data:friction factor=0.020V= 8cfsPipe 1Length=2750ftdiameter=21inPipe…

Q: Pipes

Q: A

Q: Q1: For the figure shown, determine peak flow at manhole M2 at 10 min after rain started. Consider…

Q: A residential area located in an urban zone of Basrah governorate is served by the triangular pipes…

Q: PROBLEM 7 The discharge of water In the system shown below Is 0.1 m/s, x-1.0 m. y- 2.0 m, 2- 7.0m,…

A: Given Discharge 0.1 m^3/sec No loss Diameter of pipe 30 cm Diameter of nozzle 10 cm

Q: temperature is 10°C. Assume turbulent flow at all locations. What is the pressure at point B? V…

Q: Two rectangular clarifiers which are connected in series, each 50 m long and 15 m wide with water…

A: For Two rectangular clarifiers which are connected in series,Length,L 50 mWidth,B= 15 m wide Depth…

Q: Oil (SG = 0.89), with a kinematic viscosity of 0.007 ft2/s, flows in a 3-in.-diameter pipe at 0.049…

Q: Q6. Absolute vapor pressure of water siphoned is 2.25 kPa. Water is extracted from a reservoir as…

A: Given that: Vapour Pressure of water: Pv=2.25kPaAtmospheric Pressure, Patm = 100 kPaγwater =9810…

Q: Your assigned problem: With a total flow of 14 cfs, determine the division of flow and the head loss…

Q: Determine the quantity of flow Q at the outflow end of the pipe shown in figure 4-6 of your book…

A: Elevation of the center of pipe (H1) = 513 feet Elevation of the surface of the reservoir(H2) = 537…

Q: Pipes 1,2, and 3 are parallel with each other as shown. If the energy at the inflow pipe A is 145m,…

Q: In the parallel system shown, pipe 1 has a length of 3000 ft and 20-inch in diameter. Pipe 2 is 5000…

A: Solution:

Q: Pipes 1, 2, and 3 are parallel with each other as shown.If the energy at the inflow pipe A is 147…

Q: Flow of a liquid in a smooth 3 cm pipe yields a head loss of 2 m per meter of pipe length when the…

A: Given- a pipe carrying a liquid with the mean velocity of 1m/s. Required- to find friction…

Q: Problem 2(: For the series/parallel pipe system shown, determine the flow rate in pipe 4 if the…

Q: The pipeline shown in the figure A. takes water from a reservoir and terminates in a nozzle having a…

A: The given figure is shown below:

Q: For the pipe network shown, the flow of water from A to the first junction is 0.055 cubic meter per…

A: as per the our guidelines we are suppose to solve only 3 subpart prepost question . kindly repost…

Q: Water of temperature 30° is flowing with flow rate 0.055 liters/s in a straight 50mm diameter UPVC…

Q: Pipes 1, 2, and 3 are parallel with each other as shown.If the energy at the inflow pipe A is 133…

A: Pipe 1 Diameter = 552 mm, Length = 159 m and C = 104 Pipe 2 Diameter = 676 mm, Length = 211 m and C…

Q: Nozzle

A: To calculate pressure head at point 2. Applying Bernoullis equation at point 2 and exit. Note that…

Q: The total discharge from A to B in figure is 14 cfs. Determine the discharge in each pipe if the…

Q: A pump is installed in the pipeline between reservoirs A and E as shown in the figure below. Water…

A: Given, Hazan Williams coefficient =120 discharge Q=10 ft3/s Elevation A and B is 25ft and 40 ft

Q: In the branched pipe system shown, 850 L/min of water at 10°C is flowing in a DN 100 Schedule 40…

A: Data given Q = 850 L/min = 0.0141 m3/s Total length of pipe in the lower branch, L2 = 60 m L1 = 30…

Q: Reservoirs A and D are connected by a pipeline system as shown below. The water surface elevations…

A: Given, Surface elevation of reservoir A = 100 ft Surface elevation of reservoir B = 80 ft

Q: The flow rate for the pipe system is 0.050 m³/s with a total head loss of 12 m. Use C = 120 for all…

Q: 1 Μ Figure 2 2 ↓ Δε

Q: 2000 m 45 cm ở Q= 400 litres/s 600 m 30 cm 6 FIGURE D

A: Given that....

Q: For the pipe network shown below, Problem 4(- f=0.022 for all pipes. Determine the discharge in line…

Q: For the branching pipe system shown, determine the flow in each branch. The fluid in each reservoir…

A: Given:For branch-A:L1=5000 mD1=1.5 mz1=135 mFor branch-B:L2=800 mD2=50 cm=0.5 mz2=120 mFor…

Q: 2. The total discharge from A to B in figure is 12 l/s. Determine the discharge pipes 1 and 2 if the…

A: Given Data : Total discharge from A to B = 12 l/s f = 0.035 Determine the discharge in pipe 1 and…

Q: Considering the following figure with flow from A to D, compute the total head loss front A to D if…

A: Given: discharge, Q = 1700l/s =1.7m3/s For Pipe AB , Length, L = 1000m , dia D = 900mm For Pipe 2, L…

Q: A Pipe 1 2 3 L(m) 120 180 60 D₁-8 cm -0.0288 20.0260 -0.0314 D₁-6 cm Three pipes are in parallel…

Q: s and the friction factor f is equal for all pipes, then:

A: Solution The pipes are connected in parallel then - we know that Q=Q1+Q2+Q3........1 And…

Q: Compute the friction factor for the smaller pipe when two smooth pipes are connected in series where…

Q: Determine the transition length in a 3.5-inch SCH 40 pipe, if the flow has a Reynolds # of the flow…

A: Given, Re = 2400 D = 3.5 in

Concept explainers

Pressurized pipe flow

A 15-kilometer-long pipe with a pipe diameter of one meter transports water at a speed of one meter per second. The pipe has a friction coefficient of 0.005. Calculate the frictional head loss?

Question

For the series/parallel pipes shown,
the total head loss in the system is 25 m. Determine the
flow rate in pipes 3 and 6 in L/s.

A
D₁ = 600 mm
L₁ =1000 m
n₁ = 0.011
L5 =900 m
D5=350 mm
nç = 0.012
B L3=600 m
L4-750 m
D3=400 mm C D4-300 mm D
ng= 0.013
n₁=0.011
L₂ = 1500 m
D₂ = 500 mm
n₂ = 0.012
L6 = 1200 m
D6 = 500 mm
n6=0.011
E

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step 3

VIEW

Step by step

Solved in 3 steps with 1 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

The discharge through a concrete pipe of 1 ft diameter and 3000 ft length is 1.0 cfs. What is the head loss (hf) if the water temperature is 60°F? Apply the Darcy- Weisbach equation
Determine the flow in lps on the orifice between the 2 tanks shown below.
Q6. Absolute vapor pressure of water siphoned is 2.25 kPa. Water is extracted from a reservoir as shown in figure below. Diameter of the pipe is D= 16 cm. (Patm=100 kPa, Ywater-9810 N). Please answer the following questions. (1) Zmax a) Determine the flow rate of the system. b) Determine the maximum elevation of the highest point of the piping system without causing cavitation (Zmax=?).
1. Water is following steadily through a 50 m long section of a horizontal 5-cm diameter stainless steel pipe. The water temperature is 15°C and the flow rate is 9 L/s. Determine: a.) The pressure drop over the pipe length [kPa]. b.) The head loss [m]. c.) The pumping power needed to overcome the pressure drop (assume a pump efficiency of 67%) [kW]. 9 L/s 5 cm 50 m
Determine the division of flow and head loss from A to B, if the given f=0.010 for all pipes. Note that the total flow is 10 cfs. L=4000ft D=16 inch B L=2000ft D=12 inch
The total discharge in the system below is 15.5 cfs and the head loss from B to C is 24 ft. Using n = 0.011 for all pipes, determine the following: a. head loss hl1 (ft) in pipe 1, and b. head loss his (ft) in pipe 5. 2000 ft 12 in 3000 ft 1500 ft 4000 ft 30 in 10 in 24 in А В D 2500 ft 4 15 in
For the pipe networks shown, the flow of water from reservoir A to the junction is 0.035 cu.m.per second. a) Determine Q2, Q3 b) Determine the head loss from A to B
The discharge through a concrete pipe of 1 ft diameter and 3000 ft length is 1.0 cfs. What is the head loss (hr) if the water temperature is 60°F? Apply the Darcy- Weisbach equation
Two pipes 1 and 2 are connected in series. Pipe 1 is 200 mm in diameter and 300 m long while pipe 2 is 250 mm in diameter and 200 m long. Determine the total head loss of the pipes in series neglecting minor losses if the discharge is 128 liters per second. Use f=0.02 for all pipes.
A PIPELINE WITH A PUMP LEADS TO A NOZZLE AS SHOWN. FIND THE FLON RATE WHEN PUMP DEVELOPS AN 80FEET HEAD. ASSUME HEAD LOST IN THE 8-INCH PIPE TO BE THERE TIMES ITS VELOCITY HEAD WHILE THE HEAD LOST IN THE 4-INCH PIPE TO BE TEN TIMES VELOCITY HEAD. FIND: a)COMPUTE THE FLOW RATE b) FIND THE PRESSURE HEAD AT THE SUCTION SIDE. PLEASE ANSWER IMMEDIATELY WITH COMPLETE SOLUTION THANK YOU!
Three pipes 1, 2, 3 are connected in parallel. The properties of each pipe are given in the table. The combined discharge of the three pipes is 0.61 m3/s. Use Hazen-Williams coefficient of 100 for all pipes. Use table below for the properties of the pipes. a.) calculate the total head loss (A. 181 m B. 461 m. C . 411 m. D. 731 m) b) Solve for the rate of flow in pipe 1 ( A. 0.1249 m3/s. B. 0.1645 m3/s. C. 0.1145 m3/s. D. 0.1225 m3/s). C.) c) Calculate the rate of flow in pipe 2. ( A. 0.1032 m3 /s. ,B. 0.1255 m3 /s. C. 0.7865 m3/s. D. 0.3955 m3/s)
QUESTION 2 , (a) In a rare pipe system design, there is such a case whereas the minor losses is greater than major losses. Describe the case and explain the reason why minor losses value is more than major losses value. (b) Water at 35°C flows steadily in a 4 cm,diameter pipe at velocity of 3.5 cm/s. The head loss is 0.5 m. Calculate: i) the length of theuotual pipe, ii) the pressure loss, and iii) the pumping power required to overcome this pressure drop.