For the pair of 29-lb forces applied to the handles of the crimper tool, determine the crimping force in the jaws at G. 1.75 29 2.50-- 6.25 29 lb 0.75" 0.35" 0.55 ED 0.80 6.75 29 lb Answer: Fo

Q: For the pair of 26-lb forces applied to the handles of the crimper tool, determine the crimping…

A:

Q: Shown below is a toggle clamp that exerts only a vertical clamping force on the wood block at A.…

A: The force is The length of handle is

Q: For the pair of 29-1lb forces applied to the handles of the crimper tool, determine the crimping…

A:

Q: Refer to the diagram. a) Determine the horizontal and vertical components of force which the pin at…

A:

Q: 200 1s' the Reaction A the Reactions L L Oetermine the value 2. Determine the value 9, the value The…

A:

Q: – 24 in.- D 10 in. В C - y --

A:

Q: What is the angle between the force vector and the positive direction of thex-a

A: Correct answer is option a

Q: Shown below is a toggle clamp that exerts only a vertical clamping force on the wood block at A.…

A: The force is The length of handle is

Q: Q2: Determine the force supported by each member shown in Figure 2 by using method of joint. 5m 1 AN…

A:

Q: Free body diagram required. Use paper sheet to solve

A: thank you

Q: iv) Examine the solution from the calculation if this magnitude is obtained based on the above FBD…

A:

Q: The three forces are applied to the bracket. Determine the minimum value for the magnitude of force…

A: Introduction: When the force is applied to an angle, the resultant force has two force components,…

Q: Two forces X and Y act vertically downward directly at points D and F respectively while force Z…

A: We will consider joint F into equilibrium.

Q: Solve for the horizontal and vertical components of the force at point B. Match the answers. 100 N…

A:

Q: A force F=253 N acts along AB as shown, the x-component of the force is 0.5 m B F 2 m 150 |15° -y…

A:

Q: 1.0p 1i 1860N 0,1 003 ab Answer EMC = De balk van 148 kg wordt gedragen door twee klemmen. Eén zo'n…

A: given; a=0.1mb=0.03m mass(m)=148kgweight(w)=mg                   =148*9.81…

Q: Determine the  magnitude of  force (kN) in member AB if F=76532 N , a=2.93m , b=1.42m and c=4.16m.…

A: Draw a diagram for the problem. Here, θ and α are angles as shown in the diagram.

Q: Calculate the magnitude of the force supported by the bolt at A under the action of the 1.75 KN…

A:

Q: 1. Determine the eccentricity and location (indicate your reference force) of the force on the…

A:

Q: Q1) Determine the design angle for strut AB so that the 400-lb horizontal force has a component of…

A:

Q: 600 N 600 N 40 250 N 250 N

A: Given Couple moment = 500 Nm To find Magnitude of F

Q: Two forces X and Y act vertically downward directly at points D and F respectively while force Z…

A: Given data as per question  X=553N Y=248N Z=122N a=5.7m  b=3.6m…

Q: 1. (1 point) If F is in the -y direction and has a magnitude of 4kN, what is the force in bar A A.…

A: GivenF=4kN

Q: 3- Determine the force T and C 3 kN 20 16 kN 40 8 kN

A: Data given- Need to determine T & C

Q: Resolve the 900-N force into a component P along with AB and a component Q perpendicular to AB. B…

A:

Q: 10 kN 4 Smart 3 soi non 12 kN 8 kN 6 kN Aqu.21 Azn Iml F

A: Given

Q: Q5/A) From the figure below, determine the reaction force at pin C. A 000 -0.6 m 10 kN 0.6 m 0.8 m с…

A: From the figure below, Determine the reaction force at pin C.

Q: PROBLEMS 1-Determine apair of horizontalandvertical components of the ( 340 N) force ? 340 15 00

A:

Q: Determine the y-component of the force.

A: Given   Force, F = 200 lb     Angle = 30o Find   Y component of the force, FY

Q: QI/ a) While steadily pushing the machine up on an incline surface, a person exerts 180 N force P as…

A:

Q: Determine the magnitude of the pin force at B. 0.43 m 0.61 m 125 N-In B 0.43 m 0.43 m

A:

Q: e ANSWER ALL of the given questions and show COMPLETE SOLUTION for each question.   I will rate…

A: Hi and thanks for the questions. Since you have asked multiple questions, we will solve the first…

Q: A die is being used to cut threads on a rod. If 27-lb forces are applied as shown, determine the…

A: Given data,  P= 27 lb  d=5+5=10 in  D=1.375 in

Q: | 45-lb force is required to operate the foot pedal. Determine the force exerted by the bearing 'O'…

A:

Axial Load

When a bar of the uniform cross-section is acted by a load, such that the load acts along the longitudinal axis of the bar, such kinds of loadings are known as axial loadings. In general terms, a load is an external force acting on a component. An axial load acts perpendicular to the geometric cross-section of the component. Based on the direction of the application of the load, an axial load can be tensile or compressive. The analysis of bodies under the action of axial loads is generally studied under the branch of mechanics, known as statics.