For the multi-stage amplifier shown below, giventhe followingT1: K= 0.12 mA/V?, VGS(TH) = 5 V, IDo = 6.7 mA,VGSQ = 12.5 V, RD1 = 4.7 k2, (Assume ra >> RD)T2: Ipss = 6 mA, Vp = -3 V, 1IDO = 2.9 mA, VGS =%3D-0.95 V, Rp2 = 3.6 kN. (Assume ra >> RD)T3: R1 = 48 kQ, R2 = 12 k2, Rc = 4 kQ. ro = 25 k2,andB= 200Calculate Av1, Av2, Ay3, and the overall voltage gainAVT20 VRp2RIRc0.1 uFRD1T2T322 MQ0.1 uFoss =6 mAVp =-3 VT1 DBeta0.05 µFG10 MQR2Vaso -330 Ω#100 µF2.2 kn 100 µF18 MQ0.82 k2 100 uF

Answered: Image /qna-images/answer/56093a11-6d1d-4135-a381-f450b0abee9b.jpg

For the multi-stage amplifier shown below, given the following T1: K= 0.12 mA/V², VGS(TH) = 5 V, IDQ = 6.7 mA, VGSQ = 12.5 V, RD1 = 4.7 k2, (Assume ra >> RD) T2: Ipss = 6 mA, Vp = -3 V, IpO = 2.9 mA, VGSO -0.95 V, Rp2 = 3.6 kQ. (Assume rd >> RD) T3: R 48 kΩ, R2= 12 kΩ , R4 kΩ. Γo-25 kΩ, and B= 200 Calculate Avı, Av2, Av3, and the overall voltage gain Avт 20 V RD2 RI RC 0.1 F RDI T2 T3 0.1 F loss =6 mA V=-3 V 22 MQ TI D Beta 0.05 F G 10 ΜΩ R2 Vase 330 n2 #100 uF 2.2 ka # 100 uF 18 MQ 0.82 k2 100 uF

For the multi-stage amplifier shown below, given the following T1: K= 0.12 mA/V², VGS(TH) = 5 V, IDQ = 6.7 mA, VGSQ = 12.5 V, RD1 = 4.7 k2, (Assume ra >> RD) T2: Ipss = 6 mA, Vp = -3 V, IpO = 2.9 mA, VGSO -0.95 V, Rp2 = 3.6 kQ. (Assume rd >> RD) T3: R 48 kΩ, R2= 12 kΩ , R4 kΩ. Γo-25 kΩ, and B= 200 Calculate Avı, Av2, Av3, and the overall voltage gain Avт 20 V RD2 RI RC 0.1 F RDI T2 T3 0.1 F loss =6 mA V=-3 V 22 MQ TI D Beta 0.05 F G 10 ΜΩ R2 Vase 330 n2 #100 uF 2.2 ka # 100 uF 18 MQ 0.82 k2 100 uF

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Question 7) Design a JFET amplifier network with ldss-8 mA, Ve=-4 V, R1=110 MN, R2=10 MQ. When an input AC signal V=10 mV is applied to the network, an output signal Vo=2V AC is obtained. (suppose that ra2 10R0) a) Draw the JFET amplifier network you prefer to design, and explain why you choose this network b) Explain the aims and reasons in using of all the peripheral components handled on your network c) Draw AC equivalent re model of the network (5p.) d) Draw transfer characteristic curve and derive lda and Vasa values from the characteristic curve e) Calculate Av, gm, VoD, Ro, Rs, Z; and Zn. Note: Please, do not forget using resistors and capacitors as peripheral elements whatever required for your complete design in the question (i.e. input, output terminals etc.)
Label properly the required final circuit and DC loadline. Complete the given BJT circuit. Solve for the value of the resistors and voltage supply that will satisfy the given loadline
Determine Vx and the mode of operation of the PNP transistor shown in the figure below. Assume Is = °A, B = 50, VA = 00, and Rc = 0.1 KO. 10x10-16 %3D Vcc는 2 V 1.2 V- Rc Select one: a. 0.577 V, Active Mode O b. 0.23 V, Active Mode O c. None of these d. 1.153 V, Active Mode e. 2.306 V, Saturation Mode
9m= 2.2 mA/V, Rs = 4.7 kQ, RD = 5 k0, R₂ = 7 kQ, R₁ = 400 k0, R₂ = 400 ko a) Draw the small-signal equivalent circuit of the amplifier [1 b) Find Rin c) Find Rout d) Find the voltage gain Avl Rin CCI VDD = 12 V R₁ R₂ Rs RD Cc2 KHI www RL
1. Assume that the gm of Q, is 1500 umhos for the amplifier in the following figure. a. Compute. b. If gm = 1500 umho, what is the voltage gain? What is You? d. What is the purpose of C₂? What happens if it is open? C. V 200 mV pp 10 kHz HI 0.1 μF WI Ra 1.0 MO +VDD +15 V RD 6.2 k0 C3 -EE -15 V 9₂₁ 2N5458 l₂ 2N3904 RE 15 ΚΩ 0.1 μF 22 μF
Basic Electronics
QUESTION 1o For the amplifier circuit below given Kp 2.4mA/V essume A0, Vip1.5V. Q point(1.7mA, 3.JV), VDC-10V, R135OK ohm, l2-242K ohm, R 3SKohm, R sig 2kohm Determine the value of gin ms Signal Source
Q1)For the Zener regulator circuit shown in figure ,lf Vi take the following values 10V, 15V, 20V and the circuit has the following properties (VZ=12V,R=1KQ,RL=6KQ and PZmax.=120mW)Find the following Is=IR, .IZ , IL, and VL for each input values R VL PzM
VoD +12 V For the circuit of the adjacent figure a) Given that Ip = 2.83 mA, VGS(om=-7 V and Ipss = 8 mA , find VDs and VGs.. b) If a 50 mV rms input signal is applied to the amplifier, what is the peak-to-peak output voltage? gm = 5000 µS. c) Calculate the output resistance. %3D Ro 10AF 0.1 uF R 10 L. Ra 10 MA 10kn ID= 2.83 mA, Vas (Oef)=-7V. %3D
Q1) For the circuit, exactly find:- VCEQ and ICQ respectively are equal? At ICQ = [IC(sat)]/2, so VEE is equal? At re' = 202, so the voltage gain is equal? At re' = 202, so the Zi is equal? At re' = 202, so the Zo is equal? VIN VOUT 100 + RE 1K RC 5K VEE -2V VCc 8 +8 V
Consider the circuit shown below. Vc +12 V Rc 1.2 kn 1 µF HE C2 R1 Vout 12 kn Vin 1 µF HE RL 600 n Rs 50 n R2 5 kn C3 RE 500 n ' 10 μF
Data sheet below shows design parameters for a Common Source FET Transistor amplifier.VDD = 12V , VD = 0.75 VDD , VG = 0.5 VDD , Cin = Cout = 5muF , K = 1mAV-2 , VTN = 1V , R2 = 10k and ID = 2mA Q. At DC condition,design the circuit by calculating values for VG,R1,RD,VGS,RS and gm of the FET amplifier (show all the calculated steps involved). Propose and draw the DC circuit from the calculated values.