For the mechanism shown using analytical method of analysis (vector loop), knowing that link length 02A = 40 mm, AB = 60 mm; w2= 23.75 rad/s and 02 = 55°. Determine the displacement and

Q: A horizontal crcular oil storage tank with 2,5-meter inner diameter, 5-meter length made of mild…

A: Given: The inner diameter of the tank, d = 2.5 m The length of the tank, L = 5m The thickness of the…

Q: Q - The Crank radius of a single Minder IC engine is 60mm and the diameter of the cylinder is somm.…

A:

Q: For the solid area, what is the second moment about the y axis? C. (include units with answer) For…

A:

Q: Find the area of the shape in the figure and then find the center of ?gravity 1 m 2 m

A: Given

Q: Fill in the blank which is given below Linear acceleration is equal to the product of and angular…

A:

Q: IfV1-72, V2-50 and 0-43° Determine the component about y of V2 (V2y) Va

A:

Q: Fluid Force on a Tank Wall :- In the given question/s find the fluid force on the vertical side of…

A: Write down the given value using suitable variables. Here b signifies triangle base and h signifies…

Q: 4. ㅂ 1

A:

Q: 1. Draw the projection of a point “A" which is present 40 mm above HP and 30 mm in front of VP.

A: GIVEN DATA - POINT A GIVEN , 40mm ABOVE HP AND 30mm FRONT OF VP

Q: Shown to the right is a vented tank filled to the top with ethylene glycol. The tank has a breadth…

A: Given Data: Find: Determine the magnitude of the horizontal and vertical components of force…

Q: Q3) Determine the x- and y-coordinates for the shaded area as shown in figure (3), noted that all…

A:

Q: Show dimension numbers according to a well-balanced scheme! Top Front Right Side Figure 1

A: The Answer is Below

Q: find area between line y=-2+x and y=x^(1/2) and x-axis

A:

Q: A ship has portholes to provide light and ventilation to lower decks. When there are large waves on…

A:

Q: Q1: Compute the new position of the square [A(11,11), B(21,11), C(21,21), D(11,21)] after its…

A: Consider the graph shown below for the given points.

Q: an isometric For the objects shown in orthographic projection below, construct Use the box method to…

A: Given: Draw isometric view from given orthographic projections.

Q: Q2. a) Write code to calculate the perimeter of right-angle triangle as shown in the form bellow:

A: perpendicular = L * sin ( Th) base = L* cos (Th)

Q: The disk, which has a mass of 27 kg, is subjected to the couple moment of M = (1.50 +3.3) N m, where…

A:

Q: Each section of the pipe assembly ABDEC is is parallel to one of the coordinate axes. The force F…

A:

Q: For the objects shown in isometric views in the space provided. Make below, sketch the t sure that…

A: According to the details provided in the question we need to find three projection view as below.

Q: The dynamic coefficient of viscosity m (viscosity of a fluid) is from, where v= velocity, d =…

A: Given data The dynamic coefficient of viscosity m (viscosity of a fluid) is from, where v= velocity,…

Q: A. Which of the following gives the area in square meters. B. Which of the following gives the x…

A:

Q: A petrol engine has a cylinder diameter and stroke of 110mm and 250 mm respectively. The clearance…

A: We are required to find the volume of a petrol engine whose, bore stroke and clearance volume is…

Q: In part a, total mass equals mass (mass of bike + mass of So0-Hoo + mass of Eun Yeong-Ro) is to be…

A:

Q: find the centride of area of ​​X and Y.

A:

Q: Find the sentroid of the plane area shown below. Show all the calculations. In.

A: To determine  the centroid of the given plane area

Q: Hello, I need help with the answer of 3.14 from the picture, please.

A:

Q: What is not true about a unit vector, e.g., u? dimensionless. a. It is b. Its magnitude is one. c.…

A: Among the given statements, it is required to state the statement that is not true about a unit…

Q: Statics Problem !!! Help me Part A and Part B!!!! Answer it this Problem Correctly!! Please give…

A: Step 1:  Step 2:  Step 3:

Q: Locate the coordinates of the center of gravity of the three objects illustrated in the figure.…

A: for solution refer below images.

Q: Consider the holding sprite tank shown. The tank volume remains constant. What is most nearly the…

A:

Q: Find area of the shaded part using inventor

A: Find Find the area of the shaded part.

Q: Many aspects of a gymnast's motion can be modeled by representing the gymnast by four segments…

A: Draw the given table.

Q: Find the center of gravity of the following flat, thin, homogeneous, composite objects in the…

A:

Q: i dont really understand the explanation of part b or how they used trigonometry to get that. can…

A: Part (b) For the rectangular trough:The height is derived from the formula for the volume of a…

Q: Using the following dimensional scales x' = x/l; y' = y/l; u' = u/U; v' = v/U; p' = p/(pU²); B' =…

A: Note:- As per honor code and answering guidelines I can answer first three subparts at a time.If you…

Q: Find Ix for the shape below:

A: To determine: The moment of inertia of the shape about X axis. Image: Consider a image below:

Q: rity is 10 m/s²?

A: Given Mass m = 3 kg Acceleration due to gravity, g= 10 m/s^2

Q: A petrol engine has a cylinder diameter and stroke of 120mm and 235 mm respectively. The clearance…

A: Given: Diameter of cylinder , D = 120 mm = 0.12 m Length of stroke , L = 235 mm = 0.235 m  Clearance…

Engineering Drawing

Technical drawing has been around since ancient times. As in the ancient Renaissance, complicated drawings were created, including Leonardo da Vinci's drawing. Modern engineering drawing, including its specific orthographic projection with scale conventions, began in Europe (France) during the early stages of Industrialization. L.T. C. Rolt also made some of Marc's drawings for its block-making machinery (in 1799) that also may have contributed significantly to British engineering technology. Since he learned the art of presenting three-dimensional(3D) items in a two-dimensional(2D) plane, as we now term mechanical drawing.