For the log brace shown which is pinned where the members cross. Given the weight of the log is 48 lbs find the tension in cable FE. Assume a frictionless log and ground. 4 ft C 1.25 ft A 4 25 ft 1.5 ft The tension in cable EF is H G 3 ft 2.5 ft E B lbs. D 1 ft

For the log brace shown which is pinned where the members cross. Given the weight of the log is 48 lbs find the tension in cable FE. Assume a frictionless log and ground. 4 ft C 1.25 ft A 4 25 ft 1.5 ft The tension in cable EF is H G 3 ft 2.5 ft E B lbs. D 1 ft

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter6: Beams And Cables

Section: Chapter Questions

Problem 6.88P: The 15-m-long cable supports the loads W1 and W2 as shown. Find the ratio W1/W2 for which the...

See similar textbooks

Related questions

Q: Determine the tension in each cable and the components of force reaction at D needed to support the…

A: Determine the tension in each cable and the components offorce reaction at D needed to support the…

Q: D 7.5 ft B 10 ft 5 ft 12.5 1000 lb

Q: 6F. The homogenous plate ABCD is supported by hinges along its side AB and by the cable ED.…

A: A position vector for a line representing with two end points can be obtained by subtracting the…

Q: For the structure shown in Fig.(2), determine the tension in cable ABD and the reaction at C when…

Q: 50°/ A 30° 00

Q: 3) The shear leg derrick is used to haul the 200-kg net of fish onto the dock Determine the…

A: The mass of the shear leg derrick is

Q: A uniform brass plate with area of 18 m?, has weight of 51 kg which is hold by three cables in the…

Q: 1. Determine the reactions at A and E and then find the force in each member and state whether it is…

Q: A sign that weighs 15.0 N hangs from the end of a beam of length 4 meters and weight 10 Newtons.…

A: To obtain the tension in the rope, we must balance the moment produced by the tension (T) and the…

Q: 1. A truss is loaded with 600 lb as shown. Find the internal forces in all members. Be sure to state…

Q: NOTE: This is a multi-part question. Once an answer is submitted, you will be unable to return to…

Q: Determine the tension in cable BE. There is a ball and socket joint at A. 1,000 N B 20 m 14 m D 12 m…

A: Given data: F=1000 N Need to determine the tension force in BE.

Q: Determine the forces in each of the cable AC, BD, and BE. Also find the reaction forces at point O…

A: Given : The free body diagram is, The mass of cylinder is

Question

For the log brace shown which is pinned where the members cross. Given the weight of the log is 48 lbs find the tension in cable FE.
Assume a frictionless log and ground.
4 ft
C
1.25 ft
A
K
F
1.25 ft
1.5 ft
The tension in cable EF IS
H
G
3 ft
B
E
lbs.
2.5 ft
1 ft

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1: Given data

VIEW

Step 2: Calculation

VIEW

Solution

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 3 steps with 8 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

For the log brace shown, select the set of Free Body Diagrams that would be used to solve for the tension in the rope EF given the weight of the log. Assume the ground and log are frictionless. H, 4 ft F ft A D 1.5 ft 3 ft 25 ft 2.5 ft K1.25 ft
A boom hinged at the base of a vertical mast is used to lift a 2000 lb load. Find the tension in the cable and the reaction R at the end of the boom. The angle of the boom is 40 degrees with the horizontal and the cable is 60 degrees with the vertical mast. Pls include given, formula, fbd, and solution.
A uniform horizontal strut weighs 370.0 N. One end of the strut is attached to a hinged support at the wall, and the other end of the strut is attached to a sign that weighs 170.0 N. The strut is also supported by a cable attached between the end of the strut and the wall. Assume that the entire weight of the sign is attached at the very end of the strut. 30° Restaurant Find the tension in the cable (in N). Find the force (in N) at the hinge of the strut. (Give the direction in degrees counterclockwise from the +x-axis. Assume that the +x-axis is to the right.) magnitude direction °counterclockwise from the +x-axis
TRY THIS PROBLEM AFTER YOU'VE DONE THE BF LAB 2. A force of P = 25 N is just sufficient to prevent the 20 kg cylinder from descending. Determine the required force P to begin lifting the cylinder. The rope passes over a rough peg with two and half turns. [Ans. P = 1.54 kN] %3D P.
Two lifting strops are connected at their lower ends to a common shackle from which a load of 25 kN hangs. If the ropes make angles of 32° and 42°, respectively, to the vertical, find the tension in each rope.
HW 2 A 1. A truss is loaded with 600 lb as shown. Find the internal forces in all members. Be sure to state whether the members are in tension or compression. 6fy 6ft 6ft 6ft B 6ft 600 lb 6ft 6ft 6ft 6ft 6ft 6ft
Physics for Engineering A uniform bar 3.00 m long is held by ropes at the ends making angle 60.0 and 30.0, respectively, with the horizontal. A weight of 200 N is hung 0.500 m from the left end where the 60.0 rope is attached. Find the tension in the ropes (T1 & T2) and the weight (W) of the bar. (Hint: Formulate three equations for the three unknowns, 2 equations for the 1st condition and 1 equation for the 2nd condition.)
Find the force in each member of the truss shown below. Be sure to state whether the member is in tension or compression. 8 ft B 375 lb A C 16 ft-+ 8.2 ft 500 lb OD
A boom hinged at the base of a vertical mast is used to lift a 2000 load. Find the tension in the cable and the reaction R the end of the boom. The angle of the boom is 40 degrees with the horizontal and the cable is 60 degrees with the vertical mast. Show complete solution including FBD.
Two different question I need help with. Please provide every single step and unit. Thanks.
7) Find the force in each cable needed to support the load of 300 pounds. You may want to use vectors. Note that the points A and B are on the x axis to the right and left of the y axis at a distance of 2 feet from the y axis, the point Cis on the y axis at a distance of 6 feet from the origin, and the point D is above the y axis at a height of 10 feet. 10 ft
calculate the forces on PQ and QG use sections method .