For the loaded beam that shown in Figure 3, it's required to draw the following: (a) Reactions at pin support A and roller support E. (b) The shear forces diagram to scale 1cm : 5 KN. (c) The bending moments diagram to scale 1cm:10 KN.m. Illustrate, on each diagram, the values at supports, points of loading and points of load changing. 5 KN 10 kN 5 kN 3 kN/m 2 kN/m 4 kN/m E C. D 2.0 m to 2.0 m 2.0 m 2.0 m Figure 3

For the loaded beam that shown in Figure 3, it's required to draw the following: (a) Reactions at pin support A and roller support E. (b) The shear forces diagram to scale 1cm : 5 KN. (c) The bending moments diagram to scale 1cm:10 KN.m. Illustrate, on each diagram, the values at supports, points of loading and points of load changing. 5 KN 10 kN 5 kN 3 kN/m 2 kN/m 4 kN/m E C. D 2.0 m to 2.0 m 2.0 m 2.0 m Figure 3

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A hollow aluminum box beam has the square cross- section shown in the figure. Calculate the maximum and minimum shear stresses max and min in the webs of beam due to a shear force V = 125 kN.
2) A truck and trailer combination having the axle loads as shown in the figure rolls across the simply supported beam with a span of 13 meters. Determine the maximum shear force and bending moment and draw the shear and bending moment diagrams where the maximum moment occurs. nhan P1=20 KN P2=60 KN 3m 13m 6m P3=40 KN mim
For the frame presented in the figure: (a) Draw the diagram of shear forces. (b) Draw the moment diagram. Reactions: "Ax = 18 kN + "Ay = 19 kN ↑ "Hx = 13 kN → 'Hy = 9 kN 4 5 kN/m 10 kN 55 kN-m 3. E F 15 kN В A 1m 2m 2m 2m Please be clear and include all steps
Solve the following problem i- Draw the complete shearing force and bending moment diagram for the beam shown in the figure. ii- Critically discuss your results and verify the two diagrams the missing force F 325KN. F kN 40 KN 2 m 1 m 20 kN/m 10 kN/m 7 m 3 m
Beam PORS as in Figure Q1 is pin connected at P and S. (a) Develop the shear force (V) and bending moment (M) as function of x for section RS, taking point P as the origin. (b) Draw the shear force and free body diagrams of the entire beam and indicate all important points on the diagrams. [Note: All calculations must be clearly shown] 40 kN 10 kN/m P S 20 kN.m 4 m 2 т 4 m Figure Q1
Given the propped beam with an internal hinge as shown in the figure, what is the maximum safe value of w (in kN/m) if the absolute maximum shear produced is 70 kN? (input a positive value only) Hint: RA = Rp and Rg = 8.25w (kN). Use equations instead of diagrams. W(KN m) qm BO4.SM 4,5M internal hinge
A thin beam with a solid rectangular cross-section is loaded as shown in Figure Q7 below. W W L/3 L/3 L/3 Figure Q7 What is the ratio of the maximum to nominal shear stress for the beam described in Question 7? O a. 3:2 O b. 1:4 Ос. 3:1 O d.2:1 O e. 1:2 O f. None of the provided answers are correct. O 8. 1:1
Please help solve Question 1 part B
For the beam shown below: Draw the shear force and bending moment diagrams. Where does the maximum bending stress occur? Where does the maximum shear stress occur? Find the maximum bending stress in the beam if the force P= 2 kN What would the maximum bending stress be if the same force P = 2 kN would be acting from the side (perpendicular to the page) instead of from above and where would it occur (illustrate with a diagram)? 8 m 200 mm 150 mm
Q3: For the frame shown below, draw the axial force diagram, shear force diagram and bending moment diagram for ABonk 40 kN/m B 5 m 6 m 4 m
Figure 4 below shows a 10 m length of beam with a pinned support at A and rollersupport at C. The beam carries a uniformly distributed load (UDL) of 5 kN/m acrosssection B to C and a concentrated load of 25 kN at D.a. Show the Free Body Diagram (FBD) of the beam then determine the reactionforce.b. Calculate the shear force, V. Draw Shear Force Diagram (SFD).c. Calculate the bending moment, M. Draw the Bending Moment Diagram (BMD).