For the image at the right = 36°, and 0 = 18°. What is the Force vector in cartesian form if the magnitude of the force is 369 lb? וד e Z A frictionless pulley system is designed as shown with 0 = 32° and a block that weights, W = 250 lbs. What is the tension in cable AB and cable AC? Cut for Free Body Diagram 0 A Ꮎ 3 block B

For the image at the right = 36°, and 0 = 18°. What is the Force vector in cartesian form if the magnitude of the force is 369 lb? וד e Z A frictionless pulley system is designed as shown with 0 = 32° and a block that weights, W = 250 lbs. What is the tension in cable AB and cable AC? Cut for Free Body Diagram 0 A Ꮎ 3 block B

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

2.3 Please help. Written on paper not typed on computer or keyboard please. Need help both questions. Please include all units, steps to the problem and information such as its direction or if it is in compression or tension. Thx.
name these lines
Please help. Written on paper not typed on computer or keyboard please. Need help on both questions. Please include all units, steps to the problem and information such as its direction or if it is in compression or tension. Thx.
Generate isometric drawing from multiviews using drawing tools or free - hand. Use approximate proportionate dimensions . Use plane sheet to draw or sketch isometric drawing
I need answers for problems 7, 8, and 9 pertaining to the print provided.
QUESTION 4 needs to be answered,
Hello, I need your help. Topics: Force System of a Force, Moment of a Force, Moment of a Force-Scalar Formulation, Moment of a Force-Vector Formulation, and Principle of Moment. Note: Kindly show the complete step-by-step solution. Please make sure that your handwriting is understandable and the picture of the solution is clear. I will rate you with “like/upvote” after. Thank you so much.
mmetri Each part has a constant thickness with values indicated. 2.0 mm 1.5 mm 3.0 mm 2.0 mm A shear force, S₂ is applied. This results in shear flow, shown with red arrows, which has the following values: • Shear flow in part 13, just before point 3 - 38 N/mm Shear flow in part 23, just before point 3 = 44 N/mm Shear flow in part 43, just before point 3- 44 N/mm What is the shear stress in part 35, just below point 3? Express your answer in MPa, to 2 decimal places but without the units included. You have a 3% margin of error.
ADVANCED CHEMISTRY! RATE WILL BE GIVEN! PLEASE WRITE THE COMPLETE SOLUTIONS A Steam at 400 deg C an 8,200 kilo Pascals enters a turbine and leaves at 10 kPa. What is the entropy of the leaving steam if the efficiency of the turbine is 0.76. Round the answers in to 2 decimal places. Hint: Turbine's efficiency is the ratio of work delivered by the actual turbine to the work delivered by an isentropic turbine (no entropy change) H (kJ/kg) S (kj/kg-K) 8200 kPa, 400 degrees 3137.6 6.3534 10 kPa, sat. liquid 191.832 0.6493 10 kPa, sat. vapor 2584.8 8.1511
The final answer must be correct otherwise leave . Don't provide wrong answer ,It will be downvoted.
Topic/s: Force System of a Force, Moment of a Force, Moment of a Force-Scalar Formulation,Moment of a Force-Vector Formulation, and Principle of Moment. Reminder: Kindly show the complete step-by-step solution. Please make sure that your handwriting is understandable and the picture of the solution is clear. I will rate you with “like/upvote” after. Thank you.
Question 6 a) The bore of each cylinder in a six-cylinder car engine is 45 mm and the stroke for each piston is 125 mm. calculate the cubic capacity of the engine in cubic centimetres (cm³); and calculate the clearance volume per cylinder for a compression ratio, r, of 8.75. b) The bore of each cylinder in a four-cylinder four-stroke internal combustion engine is 38 mm and the stroke of each piston is 165 mm. During testing, the engine runs at 180 revolutions per minute (rpm) with a pressure-volume indicator diagram showing a mean net area of 3.4 cm² and a diagram length of 1.2 cm. The pressure scale on the indictor diagram is set to 150 kN/m² per cm. Calculate the mean effective pressure (m.e.p) and the indicated power developed by this four-cylinder four-stroke engine. c) Figure Q6c shows a pulley system with a suspended load w of 2000 N. Calculate the following: (i) (ii) (iii) (iv) The effort force (FEffort) necessary to lift and hold a load of 2000 N. The ideal mechanical advantage…