For the given schematic, utilize the node-voltage method. There are two independent sources, one dependent source, and two 3W rated resistors. c. Solve for the unknown node voltages. d. Which of the resistors exceed their power rating? 4A652 бл. 3V +- >2U₁

Q: Express in engineering notation 89000

A: According to the question we have to find engineering notation of 89000.

Q: Convert the following hexadecimal numbers to decimal: 1C16 A8516

A: The binary number system have base 2. The binary equivalent of decimal number is obtained by taking…

Q: Decimal equivalent of Octal number (764)8 is, 502 496 498 500

A:

Q: List 3 main differences of Analog Signal and Digital Signal

A: Analog signals: Analog signals have been employed in a variety of devices to generate…

Q: can you draw this circuit probably ,,,   draw it any program software    in print font

A: The given circuit is:

Q: Which of the following is NOT included in MMDST kit? Small bell with 2 ½ inch diameter opening…

A: The solution is given below.

Q: Find Ip in A (ampere) unit if E is 11 and R is 537. (Answer should roundoff to 3 decimal places) VD…

A:

Q: QUESTION 23 A ROM chip with a 128KX8 organization has lines. data 8 128 128 K 1024

A: The solution is given below

Q: It's hard to read，  I need handwrite solution

A: Given: To find: For all circuits, i) Transfer function, ii) Magnitude response, iii) Phase…

Q: Q1/The Gray code (10110111101)= ( ) in decimal number None of them O 1753 O 869 O 1749 O 931 O 1750…

A: We need to do convert the gray code to decimal number

Q: Start No Present the Initial Values If the Hand Close to the Sensor Yes Start Measure a Temperature…

A: A flow chart is shown which represents the operation instruction of a digital non-contact infrared…

Q: If Iab is equal to 303.109∠97 and Ib is 175∠307, Ic should be

A: Current: It is the time rate of the change of the charges. It flows from high voltage to low voltage…

Q: E. Use this graphic for question 12 L1 L3 3mH 5mH L2 6mH

A: The solution is given below

Q: How MLX90614 sensor will work to measure temperature based of infrared

A: MLX90614 sensor - The MLX90614 is an infrared (IR)-based non - contact temperature sensor that can…

Q: How to calculator the resistanc

A: If you know the total current and the voltage across the whole circuit, you can find the total…

Q: 4] Write 3810 in binary notation.

A: It is the decimal number  To convert it into binary we need to divide it with 2

Q: Non Punch Trough IGBTS have voltage blocking capabilities.

A: Ans. Non punch Trough IGBTs have symmetric voltage blocking capabilities .

Q: draw truth table and waveform, make sure its correct please

A: The state table can be analysed by verifying state of each flipflop after each clock.

Q: Convert the following logic gate circuit into a Boolean expression, writing Boolean sub-expressions…

A: It is given that:

Q: Change hexa decimal number(45B1) to the decimal number

A: The representation of the number for the hexa-decimal system is given as:

Q: Compute the minimal products of sum and minimal sum of products expressions for following KMAP. Show…

A: To solve above problem, one should know about k-map. K-map is used to minimize the Boolean…

Q: The printer uses print heads. O dot matrix O thermal O laser O inkjet

A: All inkjet printer has print heads.Modern inkjet printer has various type of print heads.

Q: Decimal equivalent of Octal number (764), is, O 498 500 496 502

A: Given: The octal number is 7648.

Q: Q2 Convert (10011.011)2 to decimal.

A:

Q: For analog signals: They vary in a smooth way over time They give an output that varies continuously…

A: Analog signals: A signal is an electric or electromagnetic data which is transferred from one…

Q: 7400 TTL series IC's can operate over a temperature range of 0 to 70°C. Select one: O True O False

A: We need to tell about the given statement is true or false.

Q: Differentiate comparatively the analogue and digital representations.

A: One way to represent information is to create and sustain a direct analogy between salient…

Q: to

A: Lets given string is 'This is a sample string', we have to reverse this string and the reversed…

Nodal Analysis

In the analysis of any electric circuit, nodal analysis is the method of determining the potential difference or voltage between different nodes in an electric circuit. A node is a point where two or more branches connect each other. In the nodal analysis, the voltages are determined in the terms of branch currents. The nodal analysis is also known as the node voltage method or branch current method. The nodal analysis method is one of the several applications of Kirchhoff's Current Law (KCL).