For the frame shown, determine the reactions at pinC on member BCD.Given a =1 m; W = 70 N/m and F =140 N.%3DyFF (N)a) EW (N/m)aDBaA-2aaA. RC = -70.00i + 280.00j NB. RC = 210.00i - 455.00j NC. RC = -140.00i - 420.00j ND. RC = 105.00i + 385.00j N

The given figure is shown below:

For the frame shown, determine the reactions at pin C on member BCD. Given a =1 m; W = 70 N/m and F =140 N. %3D F F (N) a W (N/m) a D B |C a 2a a A. RC = -70.00i + 280.00j N B. RC = 210.00i - 455.00j N %3D C. RC = -140.00i - 420.00j N D. RC = 105.00i + 385.00j N %3D

For the frame shown, determine the reactions at pin C on member BCD. Given a =1 m; W = 70 N/m and F =140 N. %3D F F (N) a W (N/m) a D B |C a 2a a A. RC = -70.00i + 280.00j N B. RC = 210.00i - 455.00j N %3D C. RC = -140.00i - 420.00j N D. RC = 105.00i + 385.00j N %3D

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: 2. Determine the reaction at each support and draw the shear and bending moment diagram of the beam…

Q: 5.(e) Find the reaction at A amd B of the frame shown below. Draw the bending moment diagram? Where…

Q: USE MOMENT DISTRIBUTION METHOD Given the indeterminate beam, find the reaction at B in kN. El is…

Q: PLE The member shown in Fig. against a smooth support at B. Determine the horizontal and vertical…

Q: statics

A: 1) Maximum shear Force will occur at each support = 18 kips Maximum and moment will occur at the…

Q: A 22m-diameter three-hinged arch is subjected to concentrated loads, as shown in the figure below.…

Q: Solve the support reaction at B. 16 k :黃 2 k/ft 8 k 3k/ft A D F 12 ft8 ft- -- 9 ft- 12 ft +9 ft- 3…

Q: Q-3 The frame shown in Fig.3 is pinned at A and fixed at D, with a roller support at B. Analyse the…

A: Analyze the given frame using the slope deflection method. Fixed end moments: Span AB:…

Q: What is the vertical reaction at A for the frame shown? 2 k/ft 100 k ft 15 ft El = constant E =…

A: Given:- EI=Constant E = 29000 ksi I = 3500 in4 To find:- Reaction at A

Q: 4 Which of the following gives the reaction at D in the given beam? 300N₁ 210 N/mp 100 Nm TIT777 5m…

Q: P16.10 Vertical Both reactions and the shearing force and bending moment at section 1-1. (Ans: load…

Q: For the continuous beam shown determine the reactions over the supports. SkN/m |7kN/m 3m 2m 2m 5m

Q: The frame shown is supported by a hinge at Aand a rocker at D. The frame is acted by the force…

A: The given UVL on apan AB is transformed into point load of 12×300×5= 750N or .75KNwhich will act at…

Q: determine the reaction, moment, shear and moment diagram 23 31. 5 15 L

Q: find all reaction for the frame by the force method

A: Let's take Hc as redundant Using Theorem of least work (Force Method)

Q: 4. Determine the reactions at A and B when a = 150 mm. 500 N 240 mm B ATVS

Q: Determine the following: a. vertical reaction of the support A in kN b. horizontal reaction of the…

Q: Determine the resultant couple moment acting on the beam.

A: From the given figure, we can calculate the moment from both sides (either from right side or from…

Q: 1. DETERMINE THE REACTIONS OF A AND B. 2. DRAW THE DRAGRAM FOR BEAMS EF AND CD 800 lb/pie 800 lb/pie…

Q: Replace the system of forces acting on the frame in Fig. and a couple acting horizontally through B…

Q: 8-1/ The rocker OC drives the rack AB moving up and dowa and the rack AB drives the get whose radius…

Q: a) 12.5 kip b) 32.5 kip 10 kip/ft c) 7.5 kip 5 ft The simply-supported beam above is subjected to a…

Q: What is y-axis reaction at Support E (Reaction Ey) in KN?

A: For the given beam and loading, the y-axis reaction at support E has to be computed.

Q: SOLVE ALL EXTERNAT SUPPORT REACTIONS FOR THE BEAMS SHOWN

A: This question is related to the Structure Analysis. In this question we calculate the External…

Q: 7. Find the reactions at the supports and the deflection at point C from the restrained beam shown.…

A: Given: A fixed beam of 8.5 m with a concentrated load of 52 KN at 5 m from left end. Required:…

Q: PROBLEM 2 For the beam shown, determine the reactions at A, B and D. At B, C and D is a pin and at A…

A: Given data Find reactions at A, B and D.

Q: 14. Determine the end moments for the restrained beam shown in Fig. P-714. Ans. MA = -wo L²/30; MB =…

A: Moment-area analysis is one of the most effective methods for determining beam and frame bending…

Q: P1 12 P2 4m 3m 3m 3m Figure 3

Q: A Find the moment at A of the beam shown, El is constant. (kN m) 30 KN 40 KN 50 kN 60 kN/m ↓ 2 m 4 m…

Q: Problem 6 Using the Muller-Breslau's Principle, draw the influence lines of the following response…

Q: Problem 1: Find the reaction forces Ax, Ay, Ca, Cy and forces at point B (Bx, By) note that F₁ is…

A: A frame with inclined portion AB and horizontal portion BC is given with an internal hinge at B. To…

Q: P11.9 Select Roy as the redundant. (Ans: Rcy = 6.3 k) 3.6 klf A *1 = 3000 in.4 20 ft- B DQ I= 1000…

Q: Determine the member end moments and reactions of the frame shown. B 3m 7 m A TTTT 20 kN 4 m 5 m C D…

A: The frame is fixed at point A and point D.A point load of 20 kN acts at 3m from point B.

Q: Problem 4.7 - Curved rod ABC has the the arc length of a quarter circle centered at O. Find the…

Q: Q3: The of the moments about point C sum A due to the forces and couples acting on the bar is zero.…

Q: determine the force in member AB.5 for the truss show in fig, if the reactions at supportes A and B…

Q: Refer to Fig. STA-002. Determine the moment in (kN-m) at D. W = 8 kN/m P =40KN 2.5m 0.3m Fig.…

Q: Solve for Reactions of the following beams

A: Required : Reactions of the beams given.

Q: 714. Determine the end moments for the restrained beam shown in Fig. P-714. Ans. MA = -wĽ*/30; MB =…

Concept explainers

Matrix Algebra for Structural analysis

Structural analysis is a process in which the effects of different loads and internal forces, acting on structures and their elements are determined. This method of analysis is effective in detecting the failure loads of the structural elements and the design can be altered before commencing the construction process, which ensures proper strength and safety of the structures.

Question

For the frame shown, determine the reactions at pin
C on member BCD.
Given a =1 m; W = 70 N/m and F =140 N.
%3D
y
F
F (N)
a
) E
W (N/m)
a
D
B
a
A-
2a
a
A. RC = -70.00i + 280.00j N
B. RC = 210.00i - 455.00j N
C. RC = -140.00i - 420.00j N
D. RC = 105.00i + 385.00j N

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

Step 2

Step 3

Step 4

Step 5

Step 6

Step 7

Step 8

Step 9

Step 10

Step by step

Solved in 10 steps with 4 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

Determine the reactions at A and E if P = 920 N. The reactions are positive if to the right or up, negative if to the left or down. 3500.78 N, 3101.77 N 3050.78 N, 3110.77 N 3050.87 N, 3011.77 N 3500.78 N, 3101.77 N
I need the answer as soon as possible
A IS AT THE FIXED SUPPORT point B is 6 meters from left support, point C is 9 meters from left support . D AT THE END
C 4kN/m pin im lokN Im A THT 2m Fig.2 for the three_hinged bent in fig.2:a) find reaction at support, b)set the shear and moment equations in AC and BC ? 3m 9:55 م
this is statics and dynamics
6-Neglecting friction and the weights of the members, compute the magnitudes of the pin reactions at A and C for the folding table shown. 1.2 m -0.6 m 300 N/m Answer:RA 411 N, RC = 416 N 0.8 m -0.8 m-
PROBLEM 1: The frame loaded as shown is supported with hinges at A and D and a pin at B. Determine the reactions of the supports at A and D. 20KN. M 3m
Use the double integration method and find the reactions. Determine the following. a) EIy at 1meter from pin support b) EIy' at midspan c) EIy at 1meter from left support. ASAP
Q.22 The loading, shear force and bending moment diagrams are given in the figure. Determine the position of point of contraflexure y from support B. (4) 21Nm- -In 5KN 30 in O 4KN tending diagram 2m SFD O AND IKN
500 N a 200 mm 200 mm B J D 150 mm Fig. P7.5 and P7.6 C 100 mm 30⁰ E -200 mm- Determine the internal forces at point J when a = 0.
11. Find the moment at A of the beam shown, El is constant. (kN m) (FIG. 5) Use Area Moment Method A 2m 30 kN ↓ 2m 40 KN ↓ 2m 50 kN TE |1m| 60 kN/m 4 m B
Find couple moment produced by 250N