For the following equations, add the missing phase or state symbols: (s) or (aq) or (I). Use the "Solubility Table" to make predictions. (s) = Product is Insoluble solid (precipitate) (aq) - Product is Soluble (1) = Product is in a liquid state CuSO4 (aq) + K2S (aq) → CuS_ Ni(NO3)2 (aq) + Na2CO3(aq) → NICO3_ NaOH (aq) + HCl(aq) → NaCl_ + + K₂SO4 H₂O - + 2 NaNO3

For the following equations, add the missing phase or state symbols: (s) or (aq) or (I). Use the "Solubility Table" to make predictions. (s) = Product is Insoluble solid (precipitate) (aq) - Product is Soluble (1) = Product is in a liquid state CuSO4 (aq) + K2S (aq) → CuS_ Ni(NO3)2 (aq) + Na2CO3(aq) → NICO3_ NaOH (aq) + HCl(aq) → NaCl_ + + K₂SO4 H₂O - + 2 NaNO3

Chemistry

10th Edition

ISBN:9781305957404

Author:Steven S. Zumdahl, Susan A. Zumdahl, Donald J. DeCoste

Publisher:Steven S. Zumdahl, Susan A. Zumdahl, Donald J. DeCoste

Chapter1: Chemical Foundations

Section: Chapter Questions

Problem 1RQ: Define and explain the differences between the following terms. a. law and theory b. theory and...

See similar textbooks

Similar questions

Fe(II) can be precipitated from a slightly basic aqueous solution by bubbling oxygen through the solution, which converts Fe(II) to insoluble Fe(III): 4Fe(OH)* (aq) +40H (aq) + O₂ (g) + 2H₂O(1)→→→→→→ 4Fe(OH)3 (s) How many grams of O₂ are consumed to precipitate all of the iron in 70.0 mL of 0.0550 M Fe(II)?
Using the solution Pb(NO3)2(aq) at 2x10-3 mol/L, and Na2SO4(aq) at 2x10-3 mol/L: - give the chemical equation for the reactions if these solutions were to be mixed. - identify the ions that are present in each solution and calculate their initial concentrations (before mixing) - identify the ions that will form a precipitate when the two solutions are mixed. - If 1L of each solution are mixed, will a precipitate be formed? Why?
On a white clean paper in a good handwriting please
Be sure to specify states such as (aq) or (s). If a box is not needed leave it blank. The following molecular equation represents the reaction that occurs when aqueous solutions of silver(1) nitrate and sodium iodide are combined. AgNO3(aq) + Nal (aq) →→→Agl (s) + NaNO3(aq) Write the balanced net ionic equation for the reaction. + + + +
Consider mixing these aqueous solutions: CaBr₂ (aq) + K3PO4 (aq) Predict the products and write a complete chemical equation for the reaction.
In the reaction of 11.84 g of metallic zinc with excess copper sulfate, 6.01 g of copper metal is formed: CuSO4 (aq) + Zn (s) \rightarrow→ Cu (s) + ZnSO4 (aq) What is the percent yield of this reaction, in %? Enter the numerical value only (no units or symbols), to one decimal place. Answer value
part b
100 mL of water contain 100 mg of strontium Sr²+. What mass of solid potassium chromate K2 CrO4 should be added to this solution to precipitate 99% of the strontium contained in the solution? The only possible reaction is the precipitation of strontium chromate, SrCrO4. 87.6 g.mol-¹; KSrCrO4 = 3×10−5 Data: MK₂CrO4 194.2 g.mol-¹; Msr The answer : m 5.33 g = -
Suppose you want to measure the amount of glucose in a can of soda. You can use the data generated in this experiment to help you, but what other data would you need to collect in order to measure the concentration of glucose in the soda? In other words, what additional experimental step(s) would you perform? B I U Ꭶ X X, 14▾ A In order to measure the amount of glucose in a can of soda, one would need to prepare a series of standard solutions w/ an unknown concentrations of glucose using the 0.3M of glucose sol'n and DI water. Therefore, the glucose oxidase assay would be performed on each standard sol'n and the result values would also be measured by a spectrophotometer. A standard curve may then be plotted by absorbances and the unknown concentration of glucose. It may also be necessary to adjust the pH of the soda can sample to preform additional steps. Change Submission Submitted. Waiting on graded response. 14) Once you have collected data from the step(s) proposed in the previous…
8888
What is the minimum volume of 2.47 mol L−1 HCl(aq) required to dissolve 12.3 g Mn metal? The atomic weight of Mn is 54.94 g mol−1. Mn(s) + HCl(aq) ⟶ MnCl2(aq) + H2(g)
?