For the following, calculate the hydroxide (OH"), carbonate (CO,²) and bicarbonate (HCO3) alkalinity by the procedures (1) using alkalinity measurements alone and (2) using alkalinity plus pH measurements. The sample size is 100 mL, and 0.02 N H2SO4 solution is used as the titrant.

For the following, calculate the hydroxide (OH"), carbonate (CO,²) and bicarbonate (HCO3) alkalinity by the procedures (1) using alkalinity measurements alone and (2) using alkalinity plus pH measurements. The sample size is 100 mL, and 0.02 N H2SO4 solution is used as the titrant.

World of Chemistry, 3rd edition

3rd Edition

ISBN:9781133109655

Author:Steven S. Zumdahl, Susan L. Zumdahl, Donald J. DeCoste

Publisher:Steven S. Zumdahl, Susan L. Zumdahl, Donald J. DeCoste

Chapter16: Acids And Bases

Section: Chapter Questions

Problem 8STP

See similar textbooks

Similar questions

A 10.00-g sample of the ionic compound NaA, where A is the anion of a weak acid, was dissolved in enough water to make 100.0 mL of solution and was then titrated with 0.100 M HCl. After 500.0 mL HCl was added, the pH was 5.00. The experimenter found that 1.00 L of 0.100 M HCl was required to reach the stoichiometric point of the titration. a. What is the molar mass of NaA? b. Calculate the pH of the solution at the stoichiometric point of the titration.
The titration of 0.100 M acetic acid with 0.100 M NaOH is described in the text. What is the pH of the solution when 35.0 mL of the base has been added to 100.0 mL of 0.100 M acetic acid?
A buffer is prepared by dissolving 0.062 mol of sodium fluoride in 127 mL of 0.0399 M hydrofluoric acid. Assume no volume change after NaF is added. Calculate the pH of this buffer.
Given three acid-base indicatorsâ€”methyl orange (end point at pH 4), bromthymol blue (end point at pH 7), and phenolphthalein (end point at pH 9)â€”which would you select for the following acid-base titrations? (a) perchloric acid with an aqueous solution of ammonia (b) nitrous acid with lithium hydroxide (c) hydrobromic acid with strontium hydroxide (d) sodium fluoride with nitric acid
K4 for acetic acid is 1.7 105 at 25C. A buffer solution is made by mixing 52.1 mL of 0.122 M acetic acid with 46.1 mL of 0.182 M sodium acetate. Calculate the pH of this solution at 25C after the addition of 5.82 mL of 0.125 M NaOH.
Malonic acid (HO2CCH2CO2H) is a diprotic acid. In the titration of malonic acid w ith NaOH, stoichiometric points occur at pH = 3.9 and 8.8. A 25.00-mL sample of malonic acid of unknown concentration is titrated with 0.0984 M NaOH, requiring 31.50 mL of the NaOH solution to reach the phenolphthalein end point. Calculate the concentration of the initial malonic acid solution. (Sec Exercise 113.)
Fifty cm3 of 1.000 M nitrous acid is titrated with 0.850 M NaOH. What is the pH of the solution (a) before any NaOH is added? (b) at half-neutralization? (c) at the equivalence point? (d) when 0.10 mL less than the volume of NaOH to reach the equivalence point is added? (e) when 0.10 mL more than the volume of NaOH to reach the equivalence point is added? (f) Use your data to construct a plot similar to that shown in Figure 14.10 (pH versus volume NaOH added).
A buffer is prepared using the butyric acid/butyrate (HC4H7O2/C4H7O2)acid-base pair. The ratio of acid to base is 2.2 and Ka for butyric acid is1.54105. (a) What is the pH of this buffer? (b) Enough strong base is added to convert 15% of butyric acid to the butyrate ion. What is the pH of the resulting solution? (c) Strong acid is added to the buffer to increase its pH. What must the acid/base ratio be so that the pH increases by exactly one unit (e.g., from 2 to 3) from the answer in (a)?
A good buffer generally contains relatively equal concentrations of weak acid and conjugate base. If you wanted to buffer a solution at pH = 4.00 or pH = 10.00, how would you decide which weak acidconjugate base or weak baseconjugate acid pair to use? The second characteristic of a good buffer is good buffering capacity. What is the capacity of a buffer? How do the following buffers differ in capacity? How do they differ in pH? 0.01 M acetic acid/0.01 M sodium acetate 0.1 M acetic acid/0.1 M sodium acetate 1.0 M acetic acid/1.0 M sodium acetate
Determine the volume (in mL) of 1.00 M HC1 that must be added to 750 mL of 0.50 M HPO42 to produce a buffer with a pH of 7.00.
Marble is almost pure CaCO3. Acid rain has a devastating effect on marble statuary left outdoors. Assume that the reaction which occurs is CoCO3(s)+ H+(aq)Ca2+(aq)+HCO3(aq) Neglecting all other competing equilibria and using Tables 15.1 and 13.2, calculate (a) K for the reaction. (b) the molar solubility of CaCO3 in pure water. (c) the molar solubility of CaCO3 in acid rainwater with a pH of 4.00.
Using Figure 17.11, suggest an indicator to use in each of the following titrations: (a) The weak base pyridine is titrated with HCl. (b) Formic acid is titrated with NaOH. (c) Ethylenediamine, a weak diprotic base, is titrated with HCl. Figure 17.11 Common acid-base indicators. The color changes occur over a range of pH values. Notice that o few indicators hove color changes over two different pH ranges.