For the cross section shown below the coordinates of the centroid in reference to x-y axes shown works out to be: (Show details in calculation sheet) & -10 in O 7.57 inches and 5.79 inches 06.97 inches and 3.79 inches O 897 inches and 4.79 inches O825 inches and 8.25 inches

Q: Determine the coordinates of the centroid of the lines used as boundaries of the ea shown in Problem…

A:

Q: 1) Compute the centroid y bar with respect to its base.

A:

Q: 102.803 13 13 25 35 944618 C 55.167 128 Vor 1201344 1044933

A: Given DataAH=44.258AB=102.803BC=55.167

Q: Determine the coordinates of the centroid of the lines used as boundaries of the area shown in…

A:

Q: values of a,b,c and d in the following 3 points matrix equation a -b b+a)- ) 8. %3D 3d +c 2d-ch 17

A:

Q: Locate the centroid x and y of the cross sectional area of the angle bar

A: Given:- An angle bar is shown  To determine:- The centroid x and y of the cross-sectional area of…

Q: 25 mm 50 mm 100 mm -75 mm- C 25 mm –75 mm- 25 mm 50 mm 100 mm 25 mm -X

A:

Q: Calculate the y-component of the centroid of the area shown. 5 5 8

A: we will calculate centroid by using each section.

Q: QUESTION 11 The second moment of area about the neutral axis of the H-section shown in the figure…

A: Solution Divide the section into three-part

Q: Photographs at a scale of S are required to cover an area X-mi square. The camera has a focal length…

A: Scale = 1 : 6300 Endlap = 60% Sidelap = 30%

Q: 18 in- in 25 in 15 in X Determine the distance in the x-direction (in inches) to the centroid of the…

A: Given: A composite cross section  Required: Centroid of the given cross section in x direction

Q: What type of meridian does the figure represent?

A:

Q: For the H - section shown, Find the value of h so that Ix = Iy. %3D 20mm 100mm 20mm h = ? 20mm 140mm

A: Moment of Inertia of Rectangle about C.G =bd312From Parallel Axis Theorem :Im=IG+Ax2Where Im= Moment…

Q: Determine coordinates of centroid of the shaded area shown in the figure below *

A: Consider the figure,

Q: Problem 3 Using the provided figure below, sketch the front, top, and right views of the object…

A: To Draw the front view, side view, and the top view of the given diagram and calculate the area of…

Q: Determine the center of gravity of the shape below, provide the distance from r-t and y-y axes as…

A: To find centroid

Q: Determine the second moment of area of the shaded portion about the reference axis Y-Y shown in the…

A:

Q: Calculate the y-coordinate of the centroid of the shaded area. The triangle is equilateral. 26 54…

A:

Q: Locate the X–X and Y–Y centroidal axes for the area shown.

A:

Q: 1. The details of the cantilever beam are shown below. Use f'c = 28 MPa, fy = 415 MPa, and fyt = 275…

A: Cantilever beam: A cantilever is a rigid Structural element that can be extended horizontally and…

Q: Q.1) For the area below, find the coordinates of the centroid. 300 mm 400 mm 300 mm 300 mm

A:

Q: Please calculate elevations in the stations given in the table and show the arithmetic check. Write…

A: Given: The leveling notes are given below, Station BS (m) FS (m) H.I. (m) Elevation (m)…

Q: What is the smallest reading a vernier caliper can have if it has 20 divisions in the vernier scale?…

A: LEAST COUNT OF VERNIER CALLIPERS= VALUE OF SMALLEST DIVISION ON THE MAIN SCALE/NO OF DIVISION ON THE…

Q: Note: Replace all zero digits of your ID number by number "2" blem #5: Use X = Last 3 digits of ID…

A: To find tension in all cables

Q: A simply supported 4-m long beam is made up of 80% grade Malugai. The beam is carrying a uniform…

A:

Q: 5. The four-sided, closed figure below has the following interior angles and distances AB Bearing N…

A: Knowing the main points like distances and angles between points and contours helps engineers decide…

Q: PROBLEM 2 Determine the coordinates of the centroid of the lines shown with respect to the indicated…

A:

Q: Find the sum of the following:827144697

A: Calculate the sum of given values:

Q: Photographs at a scale of S are required to cover an area X-mi square. The camera has a focal length…

A: Area of ground=11 mi2 =11*4014489600 in2 Longitudinal overlap=60% Side overlap=30%

Q: Q6. Calculate the angle "q" in Figure 2. Enter your answer as ddd,mm,ss | bearing AB is (10+X)°…

A:

Q: express each measurement in meters0.9 centimeter

A: Given values: Measurement in cm = 0.9 cm

Q: Ø200 y Ø150 300 300 Ø50 50 50- 275

A:

Coordinate Geometry of Survey

Coordinate geometry (COGO) is a method of inserting surveying or engineering data into geographic information system (GIS), computer-aided design (CAD), or mapping software. These data can be collected on the proposed construction site using standard surveying techniques and instrumentation or may be taken from existing maps, engineering plans, drawings, or records. Data gathered on the site includes coordinates of points, bearings, and distances between points. The data are noticed and noted through conventional surveying procedures, like a traverse or layout measurement series and it can be either digital or non-digital. The maps and plans are inclusive of boundaries, divisions, and other components, and these features are shown with coordinate values, the lengths, offset distance, and bearings between them.