For the construction of a pool, the heights of the corner points given in the figure were determined with the leveling made by forming a network of 10 x 10 m squares. The reference elevation is given as Href = 95,000 m and a 5% slope is envisaged for the bottom of the pool. Calculate the amount of excavation according to the given values.

Q: A trapezoidal open channel carries water at a depth of 2m. The canal has a bottom width of 6m and a…

A:

Q: A trapezoidal channel discharges water at a rate of 45 m³/s. The wetted perimeter and area are 14 m…

A: Discharge Q=45 m3/s, Wetted perimeter P=14 mArea A=18 m2manning's constant n=0.015 It is needed to…

Q: 3. A cut slope is to made in a soil having a unit weight of 16.5 kN/m³, a cohesion of 28.8 kPa and…

A:

Q: Determine the most economical section of a rectangular channel carrying water at the rate of 0.4…

A:

Q: A rectangular channel of bed width 4.0 m has a normal depth of 1.25 m. The mean velocity in the…

A:

Q: 15.23 Use Spencer's chart to determine the value of F, for a slope with the following…

A: Assuming Fs = 1 NS=c'Fs(assumed)γH Given data, c' = 21 kN/m2 γ = 19 kN/m3  H = 17 m Therefore,…

Q: For a rock slope shown in figure belows, consider the following: i-55°, p-40.6-40. 0A-38° and…

A:

Q: A rectangular channel has a width of 3.6m with a roughness coefficient of 0.013. Compute the…

A: Solution: Given: Width (b)=3.6m Manning's Roughness Coff. (η)=0.013 Mannings equation for critical…

Q: 3. Calculate the value of frictional slope for a rectangular channel having width 5m and

A: To find : Value of frictional slope.

Q: Determine the length of back water curve caused by an affux of 5 m in a rectangular channel of width…

A: Solution: Given data: Affux=5mdepth=2mwidth=50 mSlope=1:2000n=0.03h1=2.0 mh2=5+2=7mh2-h1=5mb=50…

Q: Find the most economical cross-section of a rectangular channel which is to be dug in the rocky…

A:

Q: A storm drainage channel has the shape shown in Figure 5. It is made of unfinished concrete and has…

A: To determine the hydraulic radius and the normal discharge at different normal depth for a given…

Q: versus n for each of the five variables. What do the results suggest about the importance of the…

A:

Q: Water flows in a wide, unfinished concrete channel as shown in the figure such that a hydraulic jump…

A:

Q: Find hydraulic radius Wetted area=13.32 m2 Wetted perimeter=11.33

A: Wetted area = 13.32 m2 Wetted perimeter = 11.33 m It has been asked in the question to determine the…

Q: A dam cross-section is a square facing a water depth of D=15m. Assuming a 1m strip for analysis and…

A: Given data,  FOS for overturning = 2 D = 15 m Coefficient of friction = 0.5  To find out the…

Q: The factor of safety of an infinite soil slope shown in the figure having the properties c = 0, 0 =…

A:

Q: A hydrographic survey was conducted on a reservoir to determine its capacity by contour method. The…

A: Sounding is a method of determination of RL of a point under the water surface.

Q: An earth canal is to carry 10.8 m³/ s at a mean velocity of 0.65 m /s. the side slopes are to be 2…

A: Given data, Discharge Q = 10.8 m3/s V = 0.65 m/s Slope = 2H:1V Width = B Depth y = 0.25×width (B)…

Q: Question 7: Design an unlined irrigation canal with Discharge - 50 cumec, permissible mean velocity…

A:

Q: A rectangular canal carrying 10 cubic meters per second of water is laid on a slope of 3m per km.…

A: Discharge is defined as the volume of water displaced per unit time (sec).  The discharge of the…

Q: Determine the most economical section of a rectangular channel carrying water at the rate of 0.4…

A:

Q: A standard triangular channel is lined with fresh concrete (n=0.013) and is designed based on the…

A:

Q: Water Resources Engineering: You are given the following information for a triangular channel: Top…

A: Given data: Top width of the channel (B) = 3 m Flow (Q) = 7.23 m3/s (manning’s constant) n = 0.016

Q: to derive the safety factor formula for infinite slope stability

A:

Q: Question 6 Determine the slope of the rectangular channel with following conditions: Channel width =…

A:

Q: A trough has trapezoidal ends. The top of the through is a horizontal rectangle 50 cm by 80 cm…

A:

Q: An irrigation canal with a given cross-section is desired to be dimensioned hydraulically in the…

A: m = 2   Manning's coefficient = n = .025   Base slope = S = .008   D = 2m   f = .03

Q: If b=3 m h=6 m . Find wetted perimeter

A: Introduction : The given question is related with fluid mechanics . In this question we are provided…

Q: A square piece of land 60 m x 60 m is to be levelled down to 8 m above elevation zero. To determine…

A: Volume : Volume is a scalar quantity that represents the amount of three-dimensional space enclosed…

Q: A 45° slope as shown in figure has been excavated to a depth of 6 m in a saturated clay having the…

A:

Q: Example(): Given below a part of project. Calculate the water level at the head of the distributary…

A: The head loss in each watercourse is .The minimum allowable slope is .The length of each course is…

Q: - Define Active, Passive, and At-Rest Lateral Earthpressure. Explain using a Mohr circle why we can…

A:

Q: 2- Immediately after construction of an earth embankment, it had a height of 6m. if the settlement…

A:

Measuring site work, Excavation and Piling

Bid drawings typically include very little material about the precise requirements of site work operations, measuring site work and excavation work differs from measuring most other works on a construction project. The actual site work conditions are not provided and also the dimensions of the excavations are not known during the pre-construction phase. The precise measurement of the excavation and backfill of the earth material and topsoil is important for a contractor to decide upon the total cost required for the process. All the works should be carried out under OSHA (Occupational Safety and Health Administration) standards to ensure the safety of the workers.