For the code sequence below, state whether it must stall, can avoid stalls using only forwarding, orcan execute without stalling or forwarding.i1: addi $t1, $to, 112: addi $t2, $t1, 213: addi $t3, $t0, 214: addi $t4, $t0, 4i5: addi $t4, $t3, -116: beq $t0, $0 endend:Which lines in the program would require stalls based on data dependenciesReorder the program so that no stalls are required.

ADD R1, R2, R3SUB R4, R1, R5AND R6, R1, R7OR R8, R1, R9XOR R10, R1, R11ALUMem RegADD instruction…

For the code sequence below, state whether it must stall, can avoid stalls using only forwarding, or can execute without stalling or forwarding. i1: addi $t1, $to, 1 12: addi $t2, $t1, 2 13: addi $t3, $t0, 2 14: addi $t4, $to, 4 i5: addi $t4, $t3, -1 16: beq $t0, $0, end end: Which lines in the program would require stalls based on data dependencies

For the code sequence below, state whether it must stall, can avoid stalls using only forwarding, or can execute without stalling or forwarding. i1: addi $t1, $to, 1 12: addi $t2, $t1, 2 13: addi $t3, $t0, 2 14: addi $t4, $to, 4 i5: addi $t4, $t3, -1 16: beq $t0, $0, end end: Which lines in the program would require stalls based on data dependencies

Database System Concepts

7th Edition

ISBN:9780078022159

Author:Abraham Silberschatz Professor, Henry F. Korth, S. Sudarshan

Publisher:Abraham Silberschatz Professor, Henry F. Korth, S. Sudarshan

Chapter1: Introduction

Section: Chapter Questions

Problem 1PE

See similar textbooks

Similar questions

Which of the following snippets of MIPS assembly code implements the following C++ code fragment: if (x > y) z = x - y else z = y - x You may assume that x, y, and z map to the registers $t0, $t1, and $t2. ble $t0, $t1, foo sub $t2, $t0, $t1 b bar foo: sub $t2, $t1, $t0 bar: bgt $t0, $t1 sub $t2, $t0, $t1 b bar else: sub $t2, $t1, $t0 bar: ble $t0, $t1, foo sub $t2, $t0, $t1 foo: sub $t2, $t1, $t0 bgt $t0, $t1, foo sub $t2, $t0, $t1 b bar foo: sub $t2, $t1, $t0 bar:
Given the following code, **** Main Program org 00h ;start at program location 0000h MainProgram Movf numb1,0 addwf numb2,0 movwf answ goto $ end ;place 1st number in w register ;add 2nd number store in w reg ;store result ;trap program (jump same line) ;end of source program 1. What is the status of the C and Z flag if the following Hex numbers are given under numb1 and num2: a. Numb1 = 9F and numb2 = 61 b. Numb1 82 and numb2 = 22 c. Numb1 = 67 and numb2 = 99 =
Using C++ Language (ordered linked list & simply)
Dear Wrier it is my solution could oyu please double check this solution and confirm that your solution is correct one? The SLIP frame begins with the character 0xC0, known as the SLIP END character. Bytes in the frame are treated as either control characters or non-control characters. Non-control characters are sent as is, while control characters are replaced by a two-byte sequence. Specifically, 0x7E and 0xDD are non-control characters and are sent as is. 0xDB, 0xC0, and 0x7D are control characters and are replaced by the two-byte sequences 0xDB 0xDC, 0xDB 0xDC, and 0xDB 0xDD, respectively. The byte 0xDC is also a control character and is replaced by the two-byte sequence 0xDB 0xDD. Finally, the frame ends with the SLIP END character (0xC0). The bytes sent on the wire (after framing) are 0xC0 7E DB DD 7E C0 7D DB DC FF DB DD 0xC0. The frame begins with a flag sequence represented by the bit sequence 01111110 and denoted by the value 0x7E. Each byte in the frame undergoes encoding…
Check the following schedules, whether they are conflict serializable? S1: R1(X); W1(X); R2(X); R1(Y); W1(Y); R2(Y) S2: R1(X); W1(X); R2(X); R2(Y); R1(Y); W1(Y)
IF AL = FFH and CL=02H, then after adding both registers, what will be the value/status of ZF flag? Paragraph B I Path: p
Problem 4: Write and run a program to find the values of each destination operand: .code mov al,01101111b and al,00101101b mov al, 6Dh and al, 4Ah mov al,00001111b or al, 61h mov al,94h xor al,37h ; a. Al= ? ; b. Al= ? ; c. Al= ? ; d. Al= ?
BELOW MCQ GIVEN ANSWER CAN BE MORE THAN ONE OPTION. PLEASE PROVIDE CORRECT ANSWERS. ------------------- Q3 :- The ANSI C function below causes the program in which it runs to malfunction . Which of the following connection will help to perform function successfully ? /* Return a count of all the bits set in bytes */ int bitcount (unsigned char c) { unsigned char x , b , count =0; for (b = 0 , x= 1 ; !(x & 0x100); ++b, x <<=1) { if (x | c ) ++count; } return count; } A) change the type of x to a type larger than unsigned char. B) remove the extraneous variable b. C) change the return type to unsigned char . D) change if ( x | c) to if ( x & c) inside the for loop. E) change ! (c & 0x100) to ( x < 0x100) inside the for loop.
switch (c) { case 1: a = 10; break; case 2: a = 20; break; case 3: a = 30; break; default: a = 0; } Translate this piece of C codes into ILOC codes. Variable c and a should be stored in the activation record. Your translated codes start at address 1000 and grow to larger addresses. The address of a variable in the activation record is r_arp[@name], where r_arp is the register storing the activation record address and @name is the macro for the offset of the variable name. You may use labels instead of address number in jump/branch instructions.
Choosen answer is wrong and there is no other part to the question; it is the only one.
* The LOOP # will affect only CX O only IP All CS, CX and IP Both CX and IP non of those It can implement the complement of the interrupt flag directly True O False
These are using Bitwise operation in C. Can you help?