For the circuit shown the RMS ratting current of the Thyristor greater or Firing angle=50 Degree 1:2 -200/200V oVo 5 Ohm 50 Hz O 40A O 3.9A O 8.7A O 18.8A O 16.7A 9.8A D20A O 5.6A

Q: What is the max frequency of the MOD-10 synchronous counter?

A: Fin = input clock frequency  Fin = 1 Hz . Mod of the counter  N = 10 . Fout = Fin / N.

Q: Draw the output waveform of each circuit in Figure. Assume the RC time constant is much greater than…

A:

Q: 21. Determine the output voltage waveform for the Schmitt trigger in Figure 14-59 in relation to a 1…

A: Given circuit, Given data, Voltages:- V+=+9 VV-=-9 V Biased resistance Rb=39 kΩ Resistance R1=10 kΩ

Q: (b) 60 L₂ vor 100 mH roo 50 mH 2₁ & mH 4 mH 4 mH 3 L₂ 60 mH 2 mH L₂ 2 mH 000 LA Ly I mH Ls 2 mH La…

A:

Q: MAX VOLTAGE = 2.32V MIN = -2V PK- PK = 4.40V RMS = 1.29V Period = 930 x 10-6 s (930 us)…

A: Given data: Vpeak-peak=4.4 VT=930×10-6 sMax Voltage=2.32 V   The waveform is given as:

Q: Q1) What type of signal does the circuit in Figure produce? Determine the frequency of the output.…

A: The given circuit diagram is shown below:

Q: Design for 1 MHz oscillation Include the internal effects of the 2N3904 12V CC 8= 22 uF RBIAS ww GND…

A: To design a circuit for a 1 MHz oscillation, we can use a simple RC oscillator circuit. The internal…

Q: G: A 2 kHz sine wave with DC offset of 4V is fed to the circuit. What is the DC offset of the output…

A: We need to find out DC offset output for given circuit .

Q: What is the difference between active power, reactive power and apparent power?

A: The solution is given below

Q: What is the total reactance in Figure 13-2? 2.0 H 60 Hz 37.68 Ohms 753.6 Ohms 376.8 Ohms Figure 13 -…

A:

Q: The frequency at which this circuit operates is O 50 Hz 120 Hz 100 Hz O 60 Hz

A: In this question, we need to determine the frequency of the given waveform.we know, frequency f=1/T

Q: Vin Cy Vcc = 12 V RC 3.3 K RB 270 K Please determine the AC voltage gain. Cx 1.5 K RE Vout Cy beta =…

A: In this question we need to find the AC voltage gain

Q: When used as a power amplifier with a sinusoidal input, the output of an emitter follower is…

A: In the given questions we need to discuss about that when we used  power amplifier with a sinusoidal…

Q: 8. Determine the output voltage waveform in Figure 13-64. D2 +3 V 4.7 V 4.7 V R1 47 k2 oV out -3 V…

A: the given circuit diagram. Figure 1 From Figure 1, always one zener diode is forward biased with…

Power Measurement

According to Blondel's theorem, the total power is measured with one less number of wattmeters than the number of wires present in the system. So, a single-phase and two-wire system will require one wattmeter and a single-phase and the three-wire system will require two wattmeters, and a three-phase and the three-wire system will also require two wattmeters and a three-phase and the four-wire system will require three wattmeter devices. The wattmeter is a device that measures power using one voltage and one current input as shown in the above figure. Multiple current or voltage input pair cables are used by many power analyzers and digital storage oscilloscopes (DSOs) for measuring watts, in effect within a single instrument acting as multiple wattmeters. It is possible to measure three-phase and four-wire power with one correctly specified power analyzer.