For the circuit shown in Figure1, given that Rc = 6 KN, R L=2KN, V cc = 30 V, voltage gain Av=20v and IB = 20mA. The circuit have input signal Vin Of =4v. Determine the value of IC. +Vcc R1 R Ic Signal Output C1 Signal Input R2 RE CE Ov

Q: 6. In figure 3. If R1=100, R2=50 N, Vin=0.5V and RL=2002. Find the output voltage. 7. In figure 2.…

A:

Q: Hi i am trying to convert a pwm signal to a ramp signal, i have an output that currently generates…

A: ⁹

Q: The three resistors are: R, = R3 R4 100N The strain gauge (RsG) with the following characteristics…

A:

Q: 24 Explain the advantage of using a 4 to 20 mA current loop as an input signal compared to a 0 to…

A: Explain the advantage of using a 4 to 20 mA current loop as an input signal compared to a 0 to 5-V…

Q: Connect a thermistor (Resistance=500 – 1% per °C ) in a bridge (power supply =8V) with an…

A: Given:- Rt=500ohmα=1% per°cV=8voutput of inverting amplifier=4v at 30°t= final temperature=30°

Q: V1 -12V till $1 Key - A R3 www 24kQ R2 2400 Q1 2N3904 D1 1N4739A Vz=9 LED1 Q2 2N3904 R1 33002

A:

Q: Q1. In the circuit Figure 1, ß is in range 75 < p s150 , Determine the range in (a) Small signal…

A:

Q: b), Vin Opmp -Vout R1 18ka R2 2ka ww

A: Sketch the output waveform for the given input waveform for the given op amp circuit ?

Q: Determine the maximum voltage gain of the amplifier (O/P over I/P) with the output load RL…

A: In the given circuit R1 and R2 can be replaced by Thevinin equivalent. To find the output voltage…

Q: Design a circuit to perform the function indicated in below figure: V 10V The OV imput circuit…

A: A circuit which is designed to perform the above function will be the Bridge Rectifier.…

Q: Explain the operation of the opamp circuit in the figure. In what situations does the LED…

A: An ideal opamp is a differential amplifier with infinite gain. Even though the gain is infinite, the…

Q: Complete the table below and show your complete solution. Find the operation region (cut-off,…

A: Given

Q: For the.circuit shown, what should be the input voltage Vin if RI = 5 ohms, %3D R2 =10 ohms and Vout…

A: The given circuit is: Here, R1=5 Ω, R2=10 Ω and Vout=12 V

Q: What is the gain for OPAM in figure (a) and (b) when R₁= 2 kohm, R₁ 200 kohm. R₁ V (a) (b) www R₁ •…

A: Inverting Amplifier- An inverting amplifier takes the input through its inverting terminal through a…

Q: Q2. Find Q-point when VBB = 1V, 2 V and 3 V.. Assume VCE(sat) = 0 V. Re LOKO RB Vcc Bpc = 50 www 20…

A:

Q: 2. The circuit below is a emitter follower (the output is taken from the emitter and its voltage…

A: This question belong to small signal modelling of transister and it is in common collector…

Q: Fill in the following blanks 1- for normal operation of a PNP , the base must be -------- with…

A: We have to answer one question at a time.So Solving the question first only.

Q: Can y help me fast

A:

Q: Figure below shows a 4-bit digital-to-analogue converter of type R-2R ladder. Given the converter…

A: In a 4 bit digital to analog converter like above we can firstly find the equivalent source voltage…

Q: The base unit of the relaxation constant is Amp. sec -a N. Farad-b sec -C Amp-1.Volt.C-d

A: The base unit of the relaxation constant is  A. Amp. sec  B. Ohm Farad  C. Sec  D. Amp-1. Volt

Q: R2 741 DI R1 D2 In the circuit on the side, the input signal with a peak value of 4 V is applied…

A:

Q: Vcc For the circuit Shown in Figuye 2.5k2 If Vealor, Ba200, Ri -1ov Ir 201A Ikse

A: Vc=10 Vβ=200IB=20 μATo find R1 or RB;

Q: Q. An Oil and Gas Company has gave us a contract to design a temperature measurement instrument The…

A:

Q: true or false ?? an even two bit parity checker will output a parity error if data A=LOW data ,…

A: Given, An even two bit parity checker will output a parity error if data A=LOW, data B=HIGH, parity…

Q: build an inverting summing amplifier with 2 inputs: a 1 V DC signal anda sine wave with an amplitude…

A: Circuit Design:Use an operational amplifier (op-amp) in the inverting configuration.Connect the…

Q: c) The following stiff voltage-divider circuit in Figure Q2 (c) consists of BJT with DC gain 140.…

A: The solution is given below

Voltage Division Method

In the electronics branch, a voltage divider is required to produce a section of its input voltage as an output. This basic circuit may be prepared with two resistors or any passive elements along with the voltage source. The circuit resistors are attached in series and a voltage source is braced across these resistors. The input voltage can be transferred between the resistors in the circuit for the voltage division to occur. The SI unit of electrical resistance is ohm (Ω) or kilo-ohms (kΩ).