For the circuit in Figure 4, let Vcc = 9V, R1 = 27 kQ, R2 = 15 kQ, RE = 1.2 kQ and RC = 2.2k2. The transistor has ß = 100. If the amplifier in Figure 4 operates with Rsig= 10 kO and a load of RL=2kQ. w ww Draw the re model alternating current (ac) equivalent circuit of the amplifier. Determine the input and output impedances. Determine the voltage gain Vo/Vin and Vo/Vsig. Calculate the current gain Io/Ii.

For the circuit in Figure 4, let Vcc = 9V, R1 = 27 kQ, R2 = 15 kQ, RE = 1.2 kQ and RC = 2.2k2. The transistor has ß = 100. If the amplifier in Figure 4 operates with Rsig= 10 kO and a load of RL=2kQ. w ww Draw the re model alternating current (ac) equivalent circuit of the amplifier. Determine the input and output impedances. Determine the voltage gain Vo/Vin and Vo/Vsig. Calculate the current gain Io/Ii.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Assume for both transistors transistor current gain ß-30. Take VBE 0.7V. Design the value of RI such that output current lo 1.2mA! Choose the answer closest to what you have found. V+ = 5 V IREF 21 www R₁ 22 lo ***
The parameters of the transistor in the figure below are ß = 100 and Vy = 0.7 V. Find iç and Vea for Vs = 0.8V. Repeat for Vs =2.5V. 10 k. ic + 10 ΚΩ VCE 20 k2 15 V iB vs
show all the steps.
A common source N-channel MOSFET amplifier has an RGl = 18M2, Re2=2M2. Rp= 1.2KQ, gm= 5mS and Vi = 3mVpeak, the output voltage of the amplifier when is equal to O -540mVpp O -18mVpp O -36mVpp O -1.44Vpp
A transistor amplifier which uses a npn BJT and various passive components is shown in figure Q1. A table of components values is shown in Table Q1. For this amplifier: a) Calculate the following dc voltages and currents; VB, VE, le and lc.
Draw a r parameter ac small-signal model. The model should be correctly labelled with transistor voltages and all small-signal parameters. Detail assumptions and limitations.
what is the small signal model? ro of the transistors approach infinity
Find the operating region of the MOSFET and Vn when In = 0.2A and R=5 ohm? +1.8 V R o Vp O a. None- off the options O b. Cut-off, Vp = 0.8V O c. Triode, Vp = 0.6V O d. Saturation, Vp = 0.8V
For the circult shown in the given figure. Rc-2.4 k0, Rg-10 ko. Pmin-50, and Vcc=5 V. Determine the range of values of Vgg 50 Ic that the transistor is in saturation. Assume Vy-0.6 V and VCEsat -0.2 V. The range of values of VB8 Is VBB> 12 V Ra VAR со Va VCE OE RC Ncc
Using no analysis, what mode is the transistor in? VBB RC -5V, Vcc 20V, RB 1kN, and 1002. RC RB Vcc VBB
VIN W -VOUT Figure 1 8) What trouble in the amplifier in Figure 1(c) could cause the voltage gain to drop to 1? A) the power is off B) Rj is open C) VOUT is grounded D) Rf is open
The operating point of the npn transistor is defined by a couple of values: Icand Ver- Select one: OTrue O False In the following figure. Q, and Q: are identicaland operate in active mode. if la =9 Icz then V,V2 IC