For the cct shown:1-Determine the voltage available from the voltage doubler shown if the secondaryVoltage of the transformer is 140 V (rms).2-Determine the required PIV rating of the diodes of the figure in terms of peaksecondary Voltage Vm.( Voltage of the transformer is 140 V (rms) )+ +VmD22V= C 2VmLeeee

Answered: Image /qna-images/answer/35a4773c-fb95-4269-9c07-a629d7d23a8f.jpg

Answered: For the cct shown: 1-Determine the…

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

I need a diagram of a circuit by the transform and rectification block, using the bridge rectifier circuit (4 diodes). It can be a source of any value. You don't need to do any calculations, just a drawing of how this circuit will look, please.
A single phase – half wave controlled rectifier with freewheeling diode is supplying a load consisting series connected a resistor and an inductance from a 70.7V (RMS), 50HZ sinusoidal AC source. The firing delay of the thyristor is 90° and the load values are R=102, L=0.1 H. Define the load current expression and draw the load current by calculating for first two periods. And calculate the average values of the load voltage and current.
What is the one important difference between the characteristics of a simple switchand those of an ideal diode.
Q1 Figure Q1(a) is a full wave bridge circuit with a capacitor filter and the output waveform produced by the circuit is shown in Figure Q1(b). Assume all the diodes in the circuit have a forward voltage of 0.7 V. (a) Sketch the waveform in A, B, C and D as shown in Figure Q1(a).
Draw and explain the operation of half-wave and full-wave ( 4 diodes Bridge type ). How do they operate accordingly to the flow of charging current ?
A full-wave rectifier uses 2 diodes. The internal resistance of each diode is 20 Q. The transformer RMS secondary voltage from centre tap to each end of the secondary is 50 V and the load resistance is 980 Q. Mean load current will be
When the rms output voltage of a full-wave bridge rectifier is 26.20 V, the peak inverse voltage (PIV, in V) across the diodes (neglecting the diode drop)
In voltage regulators, Zener diodes are used to operate in Select one: a. Reverse mode b. Forward mode c. Breakdown mode 55 week 5 material Jump to...
I need the answer quickly
Determine 1) the maximum load current. 2) the mean load current .3)the rms alternating load current. 4) the DC power supplied to the load. 5) the input power to the anode circuit. 6) the rectification efficiency. 7) the percentage of regulation. 8) the ripple current. R=10°0 Vi R=10°n AC Figure (2-72) the circuit of problem (2-6). (2-7) A full-wave bridge rectifier with a 120 Vrms sinusoidal input has a load resistance of Ikn. Determine:- 1) The de voltage available at the load. 2) Find the maximum current through each diode during conduction. 3) What is the required power rating of each diode. (2-8) A zener diode has a de power dissipation of Iw and a zener voltage rating of 27v. What is the value of I, max for the device? (2-9) Calculate and draw the output voltage for the circuit shown in Figure (2-74). +100v Vo 2.2kd4 2.2kQ -100v Figure (2-74) the circuit of problem (2-10).
A load is connected in the Full Bridge rectifier circuit (Four Diodes). Usedtransformer primary voltage value is 220 V (rms). The transformer winding ratio is 1:10.Using the 0.7 V model of the diode,Load Rating: 7 K Ohmsa) How many % of conduction does each diode branch stay on?b) Find the average values of the load voltage.c) Find the average values of the load current.d) Find the effective value of the load voltage.e) Find the effective value of the load current.
How can you use a zener diode? Please choose one: a. Voltage reference b. both of the above c. constant current source D. none of the above

SEE MORE QUESTIONS

Recommended textbooks for you

Introductory Circuit Analysis (13th Edition)

Electrical Engineering

ISBN:

9780133923605

Author:

Robert L. Boylestad

Publisher:

PEARSON

Delmar's Standard Textbook Of Electricity

Electrical Engineering

ISBN:

9781337900348

Author:

Stephen L. Herman

Publisher:

Cengage Learning

Programmable Logic Controllers

Electrical Engineering

ISBN:

9780073373843

Author:

Frank D. Petruzella

Publisher:

McGraw-Hill Education

Introductory Circuit Analysis (13th Edition)

Electrical Engineering

ISBN:

9780133923605

Author:

Robert L. Boylestad

Publisher:

PEARSON

Delmar's Standard Textbook Of Electricity

Electrical Engineering

ISBN:

9781337900348

Author:

Stephen L. Herman

Publisher:

Cengage Learning

Programmable Logic Controllers

Electrical Engineering

ISBN:

9780073373843

Author:

Frank D. Petruzella

Publisher:

McGraw-Hill Education

Fundamentals of Electric Circuits

Electrical Engineering

ISBN:

9780078028229

Author:

Charles K Alexander, Matthew Sadiku

Publisher:

McGraw-Hill Education

Electric Circuits. (11th Edition)

Electrical Engineering

ISBN:

9780134746968

Author:

James W. Nilsson, Susan Riedel

Publisher:

PEARSON

Engineering Electromagnetics

Electrical Engineering

ISBN:

9780078028151

Author:

Hayt, William H. (william Hart), Jr, BUCK, John A.

Publisher:

Mcgraw-hill Education,

SEE MORE TEXTBOOKS