For the cantilever beam given in figure below, determine the maximum live concentrated load P that can be applied safely. Take f = 30 MPa, fy= 420 MPa P 240 mm -3425 Wu-20 kN/m H 7 500 mm 2.5 m 450 mm

Q: Given traffic flows for each lane group at a T junction shown in Figure below. The saturation…

A: Critical lane volume for each phase: P1: 500, P2: 250, P3:150 Sum of criticial lane volume,ΣVc =…

Q: 13. - should be located to withdraw water from slig below the surface in order to avoid sediment in…

A: The intake structures are used to safe withdrawal of water from the source, which will be discharged…

Q: 3.33 The following data are obtained from a tensile test of a 12.7-mm-diameter aluminum specimen…

A: As per the Guidelines of Bartleby We are supposed to answer only first three subparts. Ultimate…

Q: QUIZ: Determine the reactions at the supports A and B of the beam shown in figure. 6 kN/m 3 kN/m

A: Free Body diagram of the given problem:

Q: Use the method of joints to determine the force in each member of the truss shown in the figure…

A: Let height be H43H+34H = 82512H = 8H = 3.84 Calculate Support Reactions ΣFY=0AY+CY = 20sin45°AY+CY =…

Q: 4. For the figure below, the specific gravity of unknown fluid equal to .. a. 0.59 b. 1.59 C. 99.11…

A: Equating pressure at datum…

Q: P1. Determine the distance x measured from the y axis to the centroid of the area of the iangle…

A:

Q: Q3) For the circular arch shown in the figure, compute the value of "P " such that the vertical…

A:

Q: _n-coil with a temperature of 6°C and leaves it -pipes system shown in the figure below.

A: Given:- temperature=6 degree celcius change temperature=12 degree celcius To find:- diameter of all…

Q: Q12 A seismic survey was carried out for a large project to determine the nature of the substrata.…

A:

Q: Q2) Find the vertical detlection at D and rotation at B in terms of El by the unit-load method for…

A: In the virtual load or unit load method, a unit load is applied on the point where deflection and…

Q: Q1: A tensile test uses a circular test specimen that has a gage length of 50 mm and diameter = 20…

A: Given that,  gage length = 50 mm diameter = 20 mm loat at 0.2% yield point = 100,000 N gage length…

Q: Solid Mechanics Set up the appropriate equation that is used to solve for the moment of inertia…

A:

Q: A- It is required to dewater a construction site, The bottom of the construction will be Im below…

A: Q= 645.52 m3/day

Q: 30 F2 = 300 N F1 = 250 N |3D 60° A 2 m -3 m- 4 m B F3 = 500 N Determine the moment of each of the…

A:

Q: Prob.7. Workout the depreciated replacement cost of a building having the following particulars by…

A: Given that, Total life of building(n)  = 80 years  Built-up area = 400m² Total life of building in…

Q: The block is deformed into the position shown by the dashed lines. Determine the average normal…

A:

Q: The figure below shows a simply supported beam with an overbang. The beam is made of two types of…

A: Allowable stress in pine=11 Mpa Allowable stress in plywood=14 Mpa Modulus of elasticity of…

Q: From your graph, plotting the yield stress against 1/vd, you found that oo 69 MPa and k, = 0.8…

A:

Q: Analyze the given continuous beam carrying UDL of 2.5kN/m using three moment equation. Take El as…

A:

Q: 2. Clockwise interior angles observed in a closed loop traverse is given below: A 83° 30' 251° 50' C…

A:

Q: Consider the velocity field given by u = and v =- 2xy. Find the circulation around an area bounded…

A:

Q: A/Determine the dimensions of settling tank to treat 1000m/day of water with particles of 0.02mm and…

A:

Q: For the state stress shown in figure below, determine the principle stresses and the maximum…

A:

Q: 2- A rectangular channel with bottom width =8.0m, Manning roughness, n =0.01986, channel bed…

A: The flow area of the given rectangular channel is  The wetted perimeter of the given rectangular…

Q: need the answer quickly

A:

Q: Lor the beamshown in Fig.3, Compute the slop of the e latic curve at A and B Aned the oe flection at…

A: We shall apply equations of equilibrium for support reaction calculation,  ∑Fy =0 RA+RB= 12(5*1)+…

Q: Ex(1): Standard Proctor Tests was performed for a soil sample, the below data was gotten from the…

A: I have answered only the first 3 parts post other parts separately. thank you To find water conent…

Q: If you know that the following plotting position formula applies only to data that have an…

A: As given the equation is: 4k+6k=9k Simplifying the equation above to calculate the value of k

Q: 8.13 A polycarbonate sample showed a craze growth length and time relation- ship of e=k log(t/to).…

A: Following is the given relationship between the craze growth length and time of the polycarbonate…

Q: 8.1: Use the virtual work method to determine the horizontal and vertical deflections at joint B of…

A: Due to issue in Math type , providing handwritten solution

Q: Q2/ For the truss shown in the figure find: 1. Rotation at member ED. L/A = 2 for all members 2.…

A:

Q: F10-2. Determine the moment of inertia of the shaded area about thex axis,

A: step 1-

Q: The ratio of total passive earth pressure to the total active earth pressure for saturated clay…

A:

Q: Problem 16.1. Determine. · the deflection at point D of the beam shown below. El is By the moment-…

A: Moment Area Method- In this method the area of the bending moment diagrams is use for finding the…

Q: is impure tricalcium silicate is impure (C3S) and dicalcium silicate (C2S). * Tobermorite,…

A:

Q: Situation 10: A soil sample has water content of 25%, degree of saturation of 80%, and specific…

A: Given data : Degree of saturation (S)=80100=0.8Water content (w)=25100=0.25Specific gravity…

Asphalt Binders and Mixtures

Asphalt binders are subsidiary products procured during the refining process of petroleum while manufacturing gasoline, diesel, and similar petroleum products. Asphalt binders are obtained from the residue that remains after the distillation of petroleum, this residue is further subjected to steam distillation and oxidation to remove the traces of gas oil present in the residue. Certain additives or modifiers are also added to asphalt binders to alter them to suit different applications.