For the below CB amplifier circuit: C5 10u w ww R1 101k R2 11.2k 12 VBE=0.63V AIHE VCC ww Q1 www Figure 1. RC 12k Q2N3904 0 RE 1k C3 HH 16u Rsig O ○ B=100 Thermal Voltage VT=26mV, Vsig=10m V. 50 C4 HH 10u Vin VOFF = 0 VAMPL= 10m FREQ = 10k AC = V1 Vout Calculate the DC bias Analysis and using the values you found for the small signal parameters. Record the calculated input and output voltages in Table 3. Given that: RL 2.6k

For the below CB amplifier circuit: C5 10u w ww R1 101k R2 11.2k 12 VBE=0.63V AIHE VCC ww Q1 www Figure 1. RC 12k Q2N3904 0 RE 1k C3 HH 16u Rsig O ○ B=100 Thermal Voltage VT=26mV, Vsig=10m V. 50 C4 HH 10u Vin VOFF = 0 VAMPL= 10m FREQ = 10k AC = V1 Vout Calculate the DC bias Analysis and using the values you found for the small signal parameters. Record the calculated input and output voltages in Table 3. Given that: RL 2.6k

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

A transistor amplifier which uses a npn BJT and various passive components is shown in figure Q1. A table of components values is shown in Table Q1. For this amplifier: a) Calculate the following dc voltages and currents; VB, VE, le and lc.
For the BJT circuit shown below, sketch the hybrid equivalent model circuit with labels of voltages, impedances, and currents. ... 1.8k0 Vo 39ka 22ko tuF-POL 10UF-POL 1200 1uF-POL 2N2221 100mv 1.5KHZ ODeg
Label properly the required final circuit and DC loadline. Complete the given BJT circuit. Solve for the value of the resistors and voltage supply that will satisfy the given loadline
Draw a r parameter ac small-signal model. The model should be correctly labelled with transistor voltages and all small-signal parameters. Detail assumptions and limitations.
1. Assume that the gm of Q, is 1500 umhos for the amplifier in the following figure. a. Compute. b. If gm = 1500 umho, what is the voltage gain? What is You? d. What is the purpose of C₂? What happens if it is open? C. V 200 mV pp 10 kHz HI 0.1 μF WI Ra 1.0 MO +VDD +15 V RD 6.2 k0 C3 -EE -15 V 9₂₁ 2N5458 l₂ 2N3904 RE 15 ΚΩ 0.1 μF 22 μF
VoD +12 V For the circuit of the adjacent figure a) Given that Ip = 2.83 mA, VGS(om=-7 V and Ipss = 8 mA , find VDs and VGs.. b) If a 50 mV rms input signal is applied to the amplifier, what is the peak-to-peak output voltage? gm = 5000 µS. c) Calculate the output resistance. %3D Ro 10AF 0.1 uF R 10 L. Ra 10 MA 10kn ID= 2.83 mA, Vas (Oef)=-7V. %3D
til Hi Determine the gain and output voltage for this operational amplifier. V1 1V R1 ww 1kQ VCC VSS R2 ww 2kQ2 U1 741
What is the power gain of the amplifier circuit in the figure? For BJT: beta(F) = hFE = 100 beta(f) = hfe = 200 VBEQ = 0,6V VT = 25mV hre = hoe = 0
Analog Electronic: Frequency Response of BJT and FET Amplifier
Q1) For the circuit, exactly find:- VCEQ and ICQ respectively are equal? At ICQ = [IC(sat)]/2, so VEE is equal? At re' = 202, so the voltage gain is equal? At re' = 202, so the Zi is equal? At re' = 202, so the Zo is equal? VIN VOUT 100 + RE 1K RC 5K VEE -2V VCc 8 +8 V
5 The transistor parameters for the circuit in Figure 5 are ß= 180 and V₁ = ∞. (a) Find Ico and VCEQ. (b) Plot the de and ac load lines. (c) Calculate the small-signal voltage gain. (d) Determine the input and output resistances R₁ and Ro. V+ = +9 V R = 10 ΚΩ Rib \ Rs=1kQ CCI HH BR₂ = V₂ 10 kQ2 V=-9 V CC₂ RE= 500 92 Ro Ovo R₁ = 300 £2
Assuming and ideal current source with infinite output impedance for the current source I, draw small signal model for the below circuit to calculate its voltage gain, input impedance and output impedance of the below circuit in terms of transistor gm, transistor r, and Rg. VOD Vout RG Vino