Answered: For the beam shown in figure 9, solve…

For the beam shown in figure 9, solve for the fixed end moment (FEM) at joint B in kN-m. Use a = 12.7 kN/m, b = 25.7 kN/m and c = 40.5 kN. Enter absolute value only

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

1. Figure 1 shows a frame carrying a uniformly distributed load of 36 kN/m on span BC. Supports A and D are fixed. El is not constant as shown in the figure. 36 kN/m B 1.51 3 m I A D 1.5 m 3 m 1.5 m Figure 1 a) Compute the internal moments at the joint of the frame by using the Slope Deflection Method.
ST 2 SOLVE AND GIVE THE COMPLETE SOLUTION
a) The truss structure in Figure Q4 is supported at A and D with downward vertical load F1 acting at joint E and a downward vertical load F2 acting at joint C. The length of each truss member AB, BE, BC, CD and CF is 1.25 m. If F1 = 95 kN and F2 = 225 kN, determine the reaction force RA and RD at the supports A and D. Give your answers in kilonewtons (kN) to two decimal places. F1 E A В F2 Figure Q4 b) For the truss structure in Figure Q4, determine the forces FAE, FAB and FCF acting in members AE, AB & CF and clearly state if each member is in compression or in tension. Give your answers in kilonewtons (kN) to two decimal places. c) A solid homogeneous truss tie-rod has a diameter of 9.52 mm and an original length of 1.75 m experiences a stress of 600 MPa when placed under tension. If the material used for the truss tie-rod has a Young's Modulus, E, of 5.8 x 1011 N/m², calculate: (i) the tie-rod's extension in millimetres (mm); (ii) the strain energy (U) in Joules; and (ii) the strain…
Problem: Analyze the given indeterminate beam by computing the support reactios. Use Three Moment Equation. El is assumed to be constant throughout the entire span of the beam. 3 KN 2 m 3 kN/m 4 m 5 kN/m 6 m
P= 13 kN In the given figure, all the dimensions, loading condition and cross-section of the beam are given. If the allowable tension stress om= 120 MPa and the allowable compression stress oeme=100 MPa ; q=2 kN/m \B 4m 1m a) Construct the internal force diagrams (N, T, M). b) Calculate the moments of inertia (I, I, I„.). c) Check whether the beam can carry the given loading safely. К.С. 2cm 8cm 2cm 4 сm C. |G X+ 9 cm Note: The modulus of elasticity in the material is E=200 GPa, K.Ç. :Line of forces Kiriş enkesiti
Show complete solution. Dont round off initial values, only round off in final answer ty
Determine the bending moment (M) in kNm at the point x = 4.5 m from point A for the beam as loaded in Figure 3.2b6. Given a = 2, b = 5 and w4 = 6. Wą kN/m C В a m b m
Asap and solve correctly
Determine the moments over the supports using three moment equation. Also determine the support reactions. The answers are given show the solution *USE THREE MOMENT EQUATION
A rectangular beam120 mm wide by 400 mm deep is loaded as shown in the figure. a) Determine the value of P if w = 3kN/m to cause a maximum bending stress of 10 MPa. b) Determine the value of the moment at the point of application of P.
Dont round off initial values, round off in final answer only. Pls show complete solution