For the attenuator circuit shown, assume C1 and C2 to be very large (∞) capacitors. Don’t be thrown off by the capacitors (How do they behave at DC? How do they behave at AC if C =∞). Assume D1 and D2 are identical diodes with n=1, V T = 25 mV (use the exponential model). a. Determine the value of the dc voltage, V_N when I = 1mA. b. Draw the small-signal equivalent circuit, replacing the diodes with their small signal resistive model, r_d. c. Determine the value of V_o/V_s when I = 1mA.

Q: In the circuit of the following figure, the input voltage Vs is 15 volts rms with a frequency of 60…

A: Input voltage Vs=15 V  (rms) Frequency f=60 Hz Resistance R=150 ohms Capacitance C=100,000 pF Vd=0.2…

Q: The diodes in the circuit depicted can be modelled as ideal diodes with an 0.7 V diode drop. The…

A: Forward voltage drop across diode=0.7VVin=1V(peak)

Q: Describe the operating principle and characteristics of a typical Zener diode found in the market…

A: Since you have posted multiple questions, we will solve the first question for you. If you require…

Q: 1) Diode half-wave rectifier a) Consider the half-wave rectified sinewave voltage waveform at the…

A: The  output waveform of the half-wave rectifier,

Q: In the circuit given in the figure, since Vi is a square wave with a frequency of 1 kHz and an…

A: According to the question, for the given circuit as shown belowVi is a square wave with a frequency…

Q: Q4) For the Zener regulated power supply shown below the rms value of vs is 15 V, the operating…

A: According to the question we have to find, Find Voutput & find the ripple voltage.

Q: 5. A voltage source produces a "Triangle" wave and is connected to a series diode and resistor…

A: The given circuit isWe need to determine which graph is best represents the voltage across the…

Q: 4. A biased clamper is connected to a rectangular AC input with 20V on the positive half cycle and…

A: We need to analyse the given clampper circuit.

Q: + There are two questions, first about an ideal diode and then about a modeled diode. For the…

A:

Analysis of Diode

It is a semiconductor device in electronics applications where only a one-way current is required. It is like a one-way switch that allows current to flow in one direction only. A diode has two terminals, a cathode, and an anode. The cathode is the negative terminal that carries electrons, while the anode is the positive terminal that carries holes. Although no element has holes, it just means that there is a free space for electrons. Diodes are used to convert AC to DC. As we know, AC shifts between positive and negative cycles and DC stays positive constantly. As the diodes allow current only in one direction, they filter out the AC signal’s negative cycle and only keep the positive one.

Working and Construction

In civil engineering, construction means the application of principles of science and mathematics for building bridges, dams, buildings, roads, highways, tunnels, airports, structures, etc. Different branches of science, like physics and chemistry, are extensively applied to design and analysis in construction. Material properties, the science of atmospheric conditions (like solutions, mixtures, etc.), the impact of environmental factors like, corrosion and acidity are some of the primary knowledge of chemistry which are used by civil engineers to carry out construction. Estimation of forces, application of laws of mechanics, fluids mechanics, soil mechanics, etc. are some of the fundamental concepts of physics, which are well applied in construction works. Building construction and structural engineering are two of the most primary areas in civil engineering that parallelly applies principles of both chemistry and physics to carry on construction works.

Property of Diode

An electronic component that facilitates the directional flow of current is known as a diode. According to the direction of the flow of current, the resistance of a diode changes from zero to Infinity.