For the amplifier circuit shown, determine the current gain Ai= lo/ls using ideal feedback equation.+Vcc0.1mADe current sourceQ2Vo(t)20KO01lo(t)1KO2KO1mAIst)0.1ΚΩDc current sourcehfel = hfe2 = 100, hiel = 30KQ , and hie2 = 1.5KQSelect one:O a. - 0.9952.O b. 1.049.O c. - 4.458.O d. 8.356.

Given data is- hfe1=hfe2=100hie1=30 kΩhie2=1.5 kΩRL=1 kΩRC=0.1 kΩ Calculating Current gain A=I∘Is

For the amplifier circuit shown, determine the current gain Ai = lo/Ils using ideal feedback equation. 0.1mA De current source 20KO Volt 01 2KO lo(t) 1KO 1mA Ist) 0.1KO De current source hfel = hfe2 = 100, hiel =30KQ , and hie2 = 1.5KO

For the amplifier circuit shown, determine the current gain Ai = lo/Ils using ideal feedback equation. 0.1mA De current source 20KO Volt 01 2KO lo(t) 1KO 1mA Ist) 0.1KO De current source hfel = hfe2 = 100, hiel =30KQ , and hie2 = 1.5KO

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

(2) ukäi Q) In the negative feedback, which of the following * .statement is true (a) Gain, noise, distortion as well as the bandwidth of the amplifier are decreases. (b) The feedback is out of phase with their input signal and the the gain stability decreases. (c) It is called regenerative and used in amplifiers. (d) The input voltage is reduced and the input and output impedances are improved.
Find the desired values below in the feedback amplifier circuit in the figure. a) Voltage and current in amplifier circuit when Rf resistor is open circuit and RL resistor is present Show step-by-step the formula that gives the profit. b) Step of the formula showing the feedback current gain Ai when the Rf feedback resistor is connected find step.
Given in the figure is a two-stage amplifier design that employs negative feedback. Answer the following questions. Use the notation (R1 + R2 + ... + Rn) for series resistors and (R1 || R2 || ... || Rn) for parallel resistors for clarity and ease. Assume that the transistors are already biased properly in the saturation region and ro1 = ro2 → ∞. Also assume that the capacitors have infinite capacitance. 1.) Find the expression for the open loop gain Av 2.) Derive the resistance Rin which is the resistance that can be seen at the input port of the amplifier
Consider the following statement: In feedback amplifiers, concerning the connections between the direct amplifiers and the feedbacks network, a shunt connectiın at the input part servers to set an increased versiın of the input impedance of the direct amplifier, whereas again a shunt connection at the output part services to set a decreased version of the output imdepance of direct amplifier. Explain what is wrong with the statement above by drawing representative circuit diagrams and outlining the necessary calculations.
The circuit uses current- (or shunt-) feedback bias. The Si transistor has ICEO = 0, VCEsat =0, and B= 100. If RC = 2k and VCC =12V, size RF for ideal maximum symmetrical swing (that is, location of the quiescent point such that VCEQ =VCC/2). +Vcc Rc Cc lic VL Cc R. -20 "ca. V -10 -12 14 -16
6
Consider the series-shunt feedback amplifier of Figure below. Assume that the voltage divider (R1, R2) is implemented with a 1-MN potentiometer. Assume that the MOSFET is %3D biased so that gm = 4 mA/V and r, is large. Also, Rp = 10 kN. VDD Find the value of R1 that results in a closed-loop gain of 5 V/V. Rp R2 R
control system, the A feedback Conerollar and procers thansfon fanction St40 GCS) = De termine a Stab le the gain K for gotem.
Şe s deve e R yuk utrerncinin ak reguamekteor. M. deyamua kalacak şekinos ie maksimum dečerini hesapie The current of a load resistance Rp is regulated with the feedback circuit shown in the figure. The Mosfet operates in saturation. What is the maximum value of Rp while M, remains in saturation? Circuit parameters / Bevre Perametreleri VREF=2.8 V, Rs=100 , w/L=54/0.18, VoD = 41 V, H,Cox = 200 µA?, VTH = 0.4 V, A = 0, A, = 00. VDD I. * RD A1 VREF Rs O a. 15.96 k O b. 23.94 k O c. 18.62 kn O d. 13.30 kn O e. 7.31 ko O f. 21.28 kO O g. 9.97 kn O h. 4.65 kn WH.