For fully developed laminar flow, you have found previously that that the average velocity is ½ of the maximum velocity. Find the relationship between average velocity and centerline velocity for turbulent flow with a profile described by: r 1/5 u = V. (1 – -) и You can use online tools to help you solve any difficult algebra. Is it reasonable to assume that the velocity profile is uniform when solving momentum and energy problems?

Q: Define external force system.

A: Forces that are present in nature can be categorized into a different section in various ways. One…

Q: One of the following is not used to reduce the setup time? a. Using power clamp b. Using softer raw…

A: The setup time can be reduced by - Eliminating waste Using power clamp Design for manufacturability…

Q: An installer can work 63⁄4 hours each day at a worksite. The installer will need303⁄8 hours to do a…

A: Given Data⇒ Time for which installer can work at a site a dayt=634 hours Time needed to install a…

Q: Find reaction at A.

A:

Q: If the mass flow rate can be expressed as m=PAV, then the averaged velocity should be O A.…

A: Given data:- Mass flow rate (m)=ρAV Where, ρ= density of flowing fluid A= area of flowing system V=…

Q: the effect of scratching the of the iron sheet surface with different objects

A: Effect of scratching the of the iron sheet surface with different objects.

Q: 3. Why is maintenance schedule needed by the maintenance team/department ?

A: Maintenance schedule is same thing as planned maintenance. It is basically required for proper…

Q: also why is Q/T0 being subtracted in sgen1 while other 2 its being added

A:

Q: Backgrour grid Exit jet

A:

Q: Draw the Ts diagram of the whole process

A:

Q: If a wind turbine is facing a wind velocity of 23.4 m/s, then it is Select one: a. Survival speed b.…

A: Solution: The maximum wind speed is also known as the maximum survival speed, is the speed above…

Q: Write down any two classifications of unplanned maintenance.

A: The two classifications of the unplanned maintenance is

Q: Vasa ship sank during its maiden voyage on 10 August 1628. Why? Select one or more: O a. The ship…

A: To choose: The correct answer. Explanation: The Vasa ship shank because of the following reasons:…

Q: means the repair work done to keep the system in good working condition.

A: we will discuss an activity/ process that is involved with work  done to keep the system in good…

Q: please explain for c) what is Sum of M at hinge

A:

Q: Q/List the properties required for Spring. Discuss the Spring materials

A: Introduction: A mechanical spring is a mechanism, also known as an elastic or resilient part, that…

Q: The value of Poisson's ratio is   a. Zero b. less than one c. one d. More than one

A: Poisson's Ratio: It is the negative of the ratio of transverse strain to the lateral strain or axial…

Q: Unit for Painting Works   a. Liters b. Gallons c. Square Meters d. All of the above

A: Painting works refer to the process of applying paint to a surface to protect, decorate, or enhance…

Q: Consider the 2D surfaces submerged in a stationary body of water, where the location of the…

A: Option (b) is correct option.

Q: which of the following will help make the service entrance more convenient? A. Service lanes should…

A: Service entrance is important for better customer attraction and to retain the customers and…

Q: Which of the following shifts can be performed on the fly? a.from four low to four high b)from four…

A: Shifts can be performed on the fly is from four high to four low. This is because In order to do…

Q: 1. Draw a FBD for the cylindrical tub before the metal object is added, clearly labeling all forces.…

A: When a body is immersed in water , the following forces acts on the body  1) Weight of the body  2)…

Q: which of the following will help make the service entrance more convenient? A. Service lanes should…

A: Given Entrance service To find Convenient entrance for service

Q: ch of the following system sgive two examples of how mechanical engineer would be involved in the…

A: (a) Passenger automobile engine: Mechanical engineers have wide scope of expertise and the…

Q: Prepare a clear sketch of the structure, showing all loads and dimensions. Use a sharp pencil and a…

A: Given Data⇒ Structure

Q: ene end is 1/3ML2. What is the angular acceleration of the rod. alpha, immediately after the string…

A:

Q: 18. Mark the one correct statement. a) Material and cross section create stress, loads resist…

A: given - multiple choice question

Q: Engineering Utilities Please answer in paragraph form. UPVOTE will be given. Discuss/Explain the…

A:

Q: Confined

A: given Identify actions required before approving Start of Work in a Confined Space.

Q: List 5 criteria of a windmill.

A: A windmill is a mechanical device or a engine that is used to converts the winds energy into…

Q: test separator and production separator

A: Required :- Short notes on test separator and production separator

Q: a) Solar energy is used to provide heat more than it used to generate electricity. b) The number of…

A: Given Solar energy Wind turbine To find Heat from solar energy Wind turbine with odd numbers

Q: What is a standpipe?

A:

Q: How much should you charge to wash alI the windows in Seattle?

A: How much should you charge to wash all the windows in seattle? Assumptions  Seattle consists of…

Buckling of columns

The column is described as a vertical member of the structure that carries an axial compressive load, and buckling is a lateral deformation of the column under the application of load.