/For equilibrium condition, determine M, and the reaction at O. 150 mm М 150 mm 60° 30° 320 N 160 mm 400 N

Q: 800 N 600 N B 0.8 m 0.4 0.4 m 0.8 m

A: By applying Newtons equations of equilibrium, we get ∑Fy=Ay=0, Ay=0N…

Q: Two reservours with different liquilds A (s.g 0.8) and B (s.g 1.5) are connected by a Im square…

A:

Q: Determine the reactions at point O, in the below figure. 210 N F = 500 N 0.125 m 0.3m- 60 0.25 m F=…

A:

Q: Problem No. 1 725 N 900 N Determine the reactions at A and B on the beam. -1 m 2 m- 1000 N m 15 m

A:

Q: Q2: Determine the horizontal and vertical couponents of reaction at A and B for the beam loaded…

A: Mechanical Equilibrium: A body is said to be in mechanical equilibrium if it satisfies the following…

Q: A 1450 N sphere is resting in a trough as shown in Figure. Determine the reactions developed at…

A:

Q: For the structure loaded as shown in the figure, determine reaction at A *

A:

Q: 2.3 x 10-13IM" 6.6 x 10 7 Jm PE(x) = Plot the potential energy curve as a function of separation…

A:

Q: Sum of all the moments acting on a body is zero, this condition represents equilibrium's اخترأحد…

A:

Q: Situation 4: Determine the support reaction at A? * 390 lb 1312 800 lb - ft 8 ft -4 ft- 3 ft 30% B

A:

Q: Q2: Determine the reactions at the Smooth contact points A,B and C 250 N 30° 0.4 m 30% 0.2 m B 0,15…

A: Given: Force by hand→F=250 N Horizontal force by hand→Fcos30°=250×cos30°=216.50 N Vertical force by…

Q: d, x+ ôt ex = 0; by ၀, + =0. by idToo дх dx dx

A: To be derived :-the equilibrium equations

Q: Reaction at A in N is Reaction atB in N is

A:

Q: 2.6. Categories of equilibrium in two- dimensions: Collinear, Concurrent at point, parallel and…

A:

Q: Q3. Determine the reactions at the pin ( A ) and the roller ( B) 80N 150 N A 44 FON 10ON

A: FREE BODY DIAGRAM is a diagram of the system which represents all the forces acting on the system.…

Q: Two reservours with different liquilds A (s.g 0.8) and B (s.g 1.5) are connected by a Im square…

A:

Q: Determine the reactions at B when angle alpha is 50°. *

A: Assume that the mass of the strut is negligible. The system has co-planar, non-concurrent forces…

Q: 4.11 Show that the hydrostatic equilibrium equation may be written d In Pgtd log P dInt kP dlog t

A:

Q: Find the magnitude of the reaction at point C

A: given - figure  to be find-magnitude of the reaction at point C

Q: Find out the reactions at supports.

A: The Given figure contains Uniform distributed load as well as Uniform varying load; Hence the…

Q: The system in the figure is in equilibrium. Determine the forces F, F, and F. y F2 (2m, 3m,-4m)…

A: Use the above figure to determine the position of force F1. Determine force F1 vector using its…

Q: 3 m 3 m 3 m E C 12 M= 59 N.M 13 3 4 50N D

A:

Q: Note: All systems are in equilibrium. 1.) What are the reactions at A and C for member ACD? The…

A:

Q: For the given system below, find the reactions of the support at O

A:

Q: Find the maximum F that can be supported, knowing that the reaction at the roller cannot exceed 4kN.…

A: A free-body diagram for a truss with a pin support at A and a roller support at B would show all the…

Q: Determine the reactions a

A:

Q: : Determine the reaction at A,E,B 6° B 12 640b

A:

Q: A В Ja P = 2400N, a = 21°,B= 60°,60 = 26° s as shown, considering the equilibrium at point-C,…

A:

Q: Question: Determine the reaction at C 200 N-m A is fixed support C is a roller

A:

Q: Determine the tension developed in cach cord required for cquilibrium of the 20-kg lamp. 45

A: Answer: (a) TCD = 339.8284 N (b) TDE = 392.4000 N (c) TAC = 242.7345 N (d) TBC = 274.6224 N

Q: Q4/ For equilibrium condition, determine M, and the reaction at O. 150 mm M 150 mm 60° 30° 320 N 160…

A:

Q: 300 N 400 N 200 N

A: The Assembly of beams to create a rigid structure is known as a truss. The basic work of a truss is…

Q: PROBLEM 2 In the figure, the roof truss is supported by a roller at A and a pin at B. Find the…

A:

Q: to kN S KN 5KN

A: To determine support reaction : We use three equilibrium condition : Take roller support as point B…

Q: C- In Fig.C, Determine the components of reaction at B. 600 N 800 N-m 1.5 m 1.5 m 2 m 2 m 45/ Fig. C

A: given data :-  M = 800 n m  P = 600 N

Q: Q/ Find the reaction forces at i point (B) 2.4 m 1.2 m- 300 kg A| O 2840 N O 1962 N O 1 kN O Non of…

A: To determine the reaction forces for the given beam, first draw the free body diagram of beam…

Chemical and Phase Equilibrium

Phase diagrams or equilibrium phase diagrams are the graphical representations that show the phase transformations of the constituting elements with respect to the pressure, temperature, and compositions. The diagrams show the conditions that limit the different phases, namely solid, liquid, and gas. The diagram can also be utilized to verify the relations between the state variables. Most of the phase diagrams are temperature-pressure phase diagrams, with the variable parameter as the composition. Usually other variables such as solubility and pressure parameters are not indicated in the phase diagram. For a one-component system (unary phase diagram), the phase diagram is generally a function of temperature and pressure as the state variables, or temperature and volume. However, for a binary system (two-phase) having two components, the phase diagram is a function of temperature and composition as the state variables only. Coexisting of the different phases of the constituting elements is indicated in the phase diagram. A ternary phase diagram can be characterized by consisting of three phases in equilibrium.