For each of the following scenario, determine which metal and or metal alloy material is best suited for? *

Q: Describe the effects of Heat Transfer?

A: The effects of heat transfer is to be mentioned.

Q: What is the material and energy balance of liquid liquid extraction process

A: Liquid-liquid extraction: Liquid-liquid extraction is a separation operation in which the solute…

Q: Which of the following is not correct statement? O a. Ductility will decrease if the carbon…

A: (a) Ductility will decrease if the carbon percentage increase in plain carbon steel. (b) Stainless…

Q: Explain what is done in anodic stripping voltammetry. Why is stripping the most sensitive…

A: Anodic stripping voltammetry is a voltammetric technique for quantitative dedication of precise…

Q: Make a comparison between thermoplastics and thermosetting polymers(a) on the basis of mechanical…

A: A resin that is solid at room temperature but becomes plastic and soft upon heating is a…

Q: 4) What is the difference between stress corrosion cracking and corrosion fatigue? Did polymer…

A: Given data 4) What is the difference between stress corrosion cracking and corrosion fatigue? Did…

Q: Which of the following materials combinations are most likely to fail due to excessive wear in the…

A: To find The material combination most likely to fail due to excessive wear in the short-medium term…

Q: Why is distillation boundary important?

A: The reason for the importance of distillation boundary is to be mentioned.

Q: Compare between the typs lubrication: liquid oil, solid oil and greases oil

A: A lubricant is a substance that helps to reduce friction between surfaces in mutual contact, which…

Q: In the laboratory experiment "Plate and Frame Filter Press" 1. Discuss its significance, and…

A: Filtration is the process of separation in which solids from the fluid sepaarted by passing through…

Q: Research about any of the following alloys and give their properties and composition. Choose at…

A:

Q: Fuel-oxidant ratio affects _____________ and _______________. flame's temperature, viscosity flame's…

A: Answer: Flame`s temperature and explosive limit pressure

Q: Define the Exergy Destruction During Heat Conduction.

A: The destruction of the exergy in the process of heat conduction is to be determined.

Q: Outline the difference between non associate and associated gas

A: Associated gas and non-associated gas both are linked with reservoirs one is produced from crude oil…

Q: Define thermoplastic, thermoset plastic and elastomer. Give some examples including chemical…

A: Definitions with examples of thermoplastic, thermosetting plastic and elastomer is asked. Effect of…

Q: Steel is an example of  __________.   A. interstitial alloy   B. ionic solid   C. molecular solid…

A: We can say steel is an example of an interstitial alloy, due to the very small carbon atoms fit into…

Q: How will you deposit corrosion resistant copper on the surface of base metal,without using any…

A: Corrosion is a process of decomposition of the metal ions by oxidation and reduction of metal in…

Q: explain what a)anode protection and b) cathode protection are and give examples of using this two…

A:

Q: Write an electron configuration for chlorine and identify the valence electronsand core electrons.

A: The electronic configuration of chlorine is to be written along with valence electrons and core…

Q: Sort the following models according to an API value: 40 oil, kerosene, oil 40, gasoline, oil 150,…

A: To sort the given list of oils as per their API values

Q: Provide an equipment description of Slurry Settler in FCC with reference:

A: To provide an equipment description of Slurry Settler in FCC (Fluid Catalytic Cracking) Dear…

Q: What if you were asked to design a tubular vessel that would minimize dispersion? What would be your…

A: The correlations between Re and Da can be used to determine Da which in-turn will give the…

Q: Given the table below and your judgement for extreme operational conditions, select polymers for the…

A: Given Data Different Material With their Glass Transition Temperature and Melting Point.  To find…

Q: How is a large surface area achieved for adsorption?

A: The technique by which surface area in large amount is obtained for the adsorption process is to be…

Q: What are the four elements of corrosion cell ? Give brief description for each of the element.

A: Corrosion cells are a complex case of Electrochemical Phenomenon. The Components and Brief…

Q: For each of the following scenario, determine which material is best suited for? ceramics composite…

A: Ceramics are compounds lies between metallic and nonmetallic elements. their interatomic bonds are…

Q: 1.write notes about high density polyethylene and low density polyethylene. 2. Advantages and…

A: Notes on HDPE and LDPE is asked.

Q: Hand Boiler Popular Culture Supporting Material/Supporting Point Supporting Material/Supporting…

A: A hand boiler is a glass sculpture used as an experimental device to demonstrate vapor-liquid…

Q: Alloying metals with impurities results in an increase in the thermal conductivity. O FALSE O TRUE…

A: Given that There are two statement given we have to choose which statement is true or false.

Q: Suggest two engineering design ideas for better efficiency of a shell of the three phase separators.

A: Hello Subscriber ! You have posted multiple questions. As per our policy, we have answered the first…

Q: Draw the diagram of a wet contact tower or packed tower ONLY of Glycol Dehydration process in a…

A: The glycol dehydrator is a complete machinery where the operation takes place in multiple steps. The…

Q: Compose a problem about Material balance with chemical reaction including 3 unit process with…

A: In the problem statement it is asked to assume a reacting system with three unit process with…

Q: List three categories of metallurgical processes?

A: Metallurgy is used to study the physical and chemical behavior of metallic elements. The domain of…

Q: What Risky-Safety Analysis is conducted during the siting of Filling/Gas Station

A: A filling station is a place where the petrol or the gas is stored, and fill the vehicles when…

Q: Problem and solution for water-in-oil emulsion separator?

A: Problems/Challenges associated with Water-in-Oil (WIO) emulsion separators Separation methods…

Q: Evaluate the performance and behavior of the carbon Steel material used in heat exchanger?

A: Introduction to the problem The goal of a heat exchanger is to transfer as much heat as possible…

Q: 1.a ) If two bituminous samples have the same consistency , describe the criteria which can be used…

A: Introduction Bitumens are viscoelastic materials without sharply defined melting points; they…