For applied load of -300N, give your strain measurement in microstrains for strain gauge 5, having first subtracted the reading obtained for zero force.

Q: Tensile load of 2 MN is applied to an Aluminium cord with original diameter of 5 mm, the measured…

A: Given: Tensile load, F = 2MN = 2 x 106 N Diameter of rod = d = 5 mm = 5 x 10-3 m Length stretched =…

Q: For good ratings, you must have to answer correctly.

A: Step 1:

Q: Define modulus of rigidity. Derive the expression for the modulus of rigidity in case of deformation…

A: Modulus of rigidity- The ratio of tangential stress to the shear strain is called as modulus of…

Q: What is the indentation diagonal length in in, when a load of 0.60 kg produces a Vickers HV of 400?

A:

Q: The pitch of a screw gauge is 0.5 mm and the head scale is divided in 100 parts. What is the least…

A: Given: pitch of screw gauge = 0.5 mm number of division on head scale = 100   To be determined:…

Q: YOUNGS MODULUS FOR A 4m LONG METAL ROD WITH A 0.50cm2 CROSS SECTIONAL AREA THAT STRETCHES 0.20cm UN

A: GivenLength of rod, L=4 mArea of rod, A=0.5 cm2=0.5×10-4 m2Strech length, ∆L=0.2 cm=0.2×10-2…

Q: The signboard truss is designed to support a horizontal wind load of 500 lb. If the resultant of…

A: Given, Wind load, W=500lb tanθ=53θ=59°

Q: A vertebra is subjected to a shearing force of 581 N. Find the shear deformation, taking the…

A: Write the given values with the suitable variables. F=581 Nh=8.99 cm=0.0899 md=4.14 cm=0.0414 m…

Q: radius which when stretched by a force of 2 kg. modulus for a wire 2 m long and 0.5 mm in Ex. 1:…

A: To find-(1) Stress(2) Strain(3) Young's modulusGiven-L=2 mr=0.5 mm=5×10-4 mF=mgF=2×9.8N

Q: A piece of copper having a rectangular cross-section of 15.2 mm × 19.1 mm is pulled in tension with…

A: Let F be the tension force, A be the area of cross-section, n be the modulus of elasticity of…

Q: Explain in detail please.

A: Take the value of the Young’s modulus from table 1, the values is  9×109 N/m2 (taken from internet,…

Q: Figure shows the stress versus strain plot for a material that is stretched by a machine pulling in…

A:

Q: The ratio of stress to strain in the initial linear is ..? * Young's modulus O viscoelasticity O…

A: In initial linear relationship stress of a material is directly proportional to strain. Stress ∝…

Q: Determine the minimum required width b for the beam and loading shown. For wood, σem =16, τem =38…

A: Draw the FBD of the beam.

Q: Given a 2m-length rod with 37.5 mm diameter what is the actual stress (in MPa) if axial load is 19.4…

A: To calculate the stress on the rod, we need to know its cross-sectional area. The cross-sectional…

Q: suppose the length of the wire between the chucks lo, were twice the length used in the experiment…

A: Elongation δL = PLAE

Q: what is the stress on a bar with n cross-sectional area of .05 sq in that is subject to a 100,000lb…

A:

Q: the shear strength parameters. b) For experiment no.1, find the effective normal and shear stresses…

A: To determine: The pore pressure in the sample at the time of collapse

Q: how can I derive formula to find the original volume, given the bulk modulus, change in volume and…

A: The bulk modulus is defined as the ratio of the volumetric stress to the volumetric strain.

Q: by I m. They found the girths to be 63 m (at eround level), 5.4 m, 4.6 m, 4.4 m, 4.8 m and 3.9 m,…

A: Solution: Given density of stone = 2800 kg/m3. Circumference of the square base section at ground…

Q: A steel rod which length is (91.44cm) and the radius (1 inch), after it pulled by a (100N) force the…

A:

Q: A vertebra is subjected to a shearing force of 497 N. Find the shear deformation, taking the…

A: Given:Shear force = 497 NHeight of cylinder = 3.2 cm = 0.032 mRadius of cylinder =…

Q: Type of strain with a symbol of epsilon * O Linear O Shear Volume (Bulk) O Strain

A:

Q: etermine the bulk modulus if a pressure of 13.2 x 10^7 N/m^2 applied to 1 kg of water causes a 6%…

A: