For a rotating shaft modeled as shown, find maRA and mgRB, placed in correc- tion planes A and B, respectively, that dynamically balance the system. Use: mı=2.2 kg, m;=1.8 kg, lA=25 cm, l=110 cm, 2=360 cm, lB=400 cm, R;=85 cm @ 95°, R2=70 cm @ 190°. mi A B mi XI X2 | l . li m2 12 IB m2

For a rotating shaft modeled as shown, find maRA and mgRB, placed in correc- tion planes A and B, respectively, that dynamically balance the system. Use: mı=2.2 kg, m;=1.8 kg, lA=25 cm, l=110 cm, 2=360 cm, lB=400 cm, R;=85 cm @ 95°, R2=70 cm @ 190°. mi A B mi XI X2 | l . li m2 12 IB m2

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Figure Q3(b) shows a uniform bar AB of mass = 8 kg hinged at point C. Point A is connected to a spring to maintain the bar in vertical direction, and the stiffness k = 500 N/m. If point A is displaced counter-clockwise by a small angle θ = 3.5 degree and released, (i) With the free body diagram and kinetic diagram, determine the initial horizontal displacement of A.
Q2) Consider a mass (m=5 kg) connected to a massless rod of length (L=2 m) to swing about point 0, as shown in Figure (2). The mauss is also connected to a spring of spring constant (k=10 N/m). The other end of the spring is connected to a pivot. The unstreteched length of the spring is I m. Find the equation of motion of the system. Nin Figure 2
The homogeneous circular disk shown in Figure A3.4 has mass moment of inertia about its centre of mass of l = 3 kgm². It rotates about a fixed shaft at its centre and is attached to a torsional spring with constant k = 20 Nm/rad. At t = 0, the angle is = 0, the angular velocity is d/dt = 4 rad/s, and the disk is subjected to an oscillatory couple M(t) = 10 sin 2t Nm. Determine as a function of time.. Figure A3.4 M(1)
5. A rod of length L, Young's modulus E, cross-sectional area A and mass density p is installed as shown. Suppose m = pAL and kL / EA =1. Find the equations of motion Open Question m www f(t) x=0 x = L/2 x= L
TORSIONAL SYSTEM Q-4 For the system in fig (4) find : rigid link k m 1. F.B.D 2. Equation of motion & wd. 3. 0(t),for < 1. 4. 8. Fig (2) B Shaft, k m Fluid, Disc, J lal Fig (4) Fig (3) www
An undamped spring/mass system, in which m = 8 slugs and the spring constant k = 16 lb/ft has a driving force f(t) = t^pi*t on [0,pi] Extend f(t) into the negative t-axis to obtain an odd function. Find the particular solution ??(?). (Note: f(t) is given as half of the period, p = π.)
L W (1) (25pts) Find the description of the linear acceleration vector of the mass center of the segment (B) as functions of the distance (r), angular displacement (0), angular velocity (0), and angular acceleration (a). (2) (bonus: 5pts) Find the mass moment of inertia of the lower leg about the knee joint. Assume that the lower leg can be modeled as a cylinder. The length of the lower leg L is 30cm, and the diameter D is 4cm. The mass of the lower leg segment is 2kg. * This is a bonus problem - you learned how to calculate the mass moment of inertia in physics.
Hello, please solve this problem. Thank you
5. Car doors are easy to slam shut but difficult to press shut by hand force. The door lock as two latches, the first easily engaged, and the second requiring the rubber seal around the door to be quite compressed before it can engage. The rubber seal gives a spring constant of 50,000N/m at the lock position for the door, and the mass moment of inertia for the door around its hinges is 2.5kg- m². The distance between the lock and the hinges is Im. Calculate what force is needed to press the car door shut at the lock if a speed of 0.8m/s at the lock slams it shut.
Draw a series analog of the translational mechanical system show in the figure. 3(1) fy = 4 N-s/m K= 5 N/m fry = 4N-s/m f()- M, = 4 kg0000 M2 = 4 kg Svz = 4 N-s/m Sv=4 N-s/m
4.35 Find the response of the mass shown in Fig. 4.56 under the force F(1) = Foe using convo- lution integral. Data: k, = 1000 N/m, k, = 500 N/m, r = 5 cm, m = 10 kg, , = 1 kg-m, Fo = 50 N. %3D Pulley, mass moment of inertia o