For a parallel plate arrangement of the type shown in Figure Q4, it is found that when the distance between plates is 2 mm, a shearing stress of 150 Pa develops at the upper plate when it is pulled at a velocity of 1 m/s. Assume the velocity distribution is linear between the plates, Determine: (ii) The kinetic viscosity of the fluid between the plates if the density of fluid is 800 kg/m³.

For a parallel plate arrangement of the type shown in Figure Q4, it is found that when the distance between plates is 2 mm, a shearing stress of 150 Pa develops at the upper plate when it is pulled at a velocity of 1 m/s. Assume the velocity distribution is linear between the plates, Determine: (ii) The kinetic viscosity of the fluid between the plates if the density of fluid is 800 kg/m³.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

2. Consider a flow with the velocity profile given by the equation below. The fluid surface is located at y = 0. Here, U∞ is called the freestream velocity and 8 is called the boundary layer thickness. Calculate the boundary layer thickness at a point where the shear stress is 36 mPa if the freestream velocity is 40 m/s and the fluid's dynamic viscosity 1.81.105 Pa.s. U.. ( 2 (²) - (²) ²) u(y) = U∞o
In mechanical fluid
In mechanical fluid
4. Consider a viscous flow inside an annular pipe. The inner surface of the pipe is located at r = R₁ and is stationary. The outer surface is located at r = Ro and moves to the right with speed Upipe. The pressure inside the pipe is constant. The fluid inside the pipe has dynamic viscosity μ. Assume that the flow is steady, incompressible, fully-developed, axisymmetric, non-rotating, and has negligible body forces. Starting from the differential form of the conservation of mass and momentum equations: a. Derive an equation for the velocity inside the pipe in terms of Upipe, R₁, Ro, and r. b. Determine the average velocity inside the pipe in terms of Upipe, R₁, and Ro. C. Determine the shear stress acting on the inner annulus in terms of Upipe, Ri, Ro, and u. Upipe er R₁ fluid
fluid mechanics explain, with examples, the effects of temperature and shear forces on newtonian and non-newtonian fluids.
1-15. Analyze the flow between two plates of Fig. 1-15 by assuming the fluid is a de Waele power-law fluid as in Eq. (1-31a). Compute (a) the velocity profile u(y) with the power n as a parameter and (b) the velocity at the midpoint h/2 for n = 0.5, 1.0, and 2.0. Answer: (b) u = V/2 for all cases 1-16. Reneat that
Oil Coating: A long, continuous belt is pulled upwards through a chemical oil bath at velocity V0. The belt has rectangular cross-section and has length (L), width into the paper (W). The belt picks up a film of oil of thickness h, density ρ, and dynamic viscosity μ. Gravity g tends to make the oil drain down, but the movement of the belt keeps the fluid from running off completely. Assume fully developed, steady, laminar, incompressible and two-dimensional flow of oil to answer the following questions. Assume that no pressure gradient is needed in the vertical direction to drive the film flow. Also assume that the shear stress at the air-oil interface is zero (free shear condition). Assume no-slip condition for the fluid in contact with the moving belt. Justify any other assumptions you may make. Show all steps. (a) Derive an expression for the two-dimensional velocity field inside the oil film in terms of the known parameters. Clearly indicate your co-ordinates and origin. You must…
Fluid Mechanics Expert Please
Consider flow of blood in the microvessels of the body, assuming Poiseuille’s law holds and that the viscosity of the blood is constant. Consider a parent vessel that bifurcates into two daughter segments, all within the microcirculation and with blood flow described using Poiseuille’s law (assume that each segment has a different diameter and length).Denoting the pressure at node i by pi (i=1,2,3,4), and the flux in segment j by Qj (j=1,2,3), write down expressions for the segment fluxes in the network, in terms of the nodal pressures. How are the three volume fluxes related, and why? Assuming that the pressures at nodes 1, 3, 4 (the boundary nodes) are known, write down an expression for the pressure at the interior node, p2.
1.A) A fluid of density ρ=850 kg/m3 and viscosity µ=0,8 Pa s is completely filling the spacing h= 2 cm between two parallel horizontal plates of length 2,5 m and width 1 m . The upper plate is pulled at a speed of U while lower plate is fixed . In order to generate a laminar steady incompressible flow of fluid in the spacing at a rate of 0,85 kg/s determine total shearing force in the field.ANSWER:10 N 1.B) A fluid of density ρ=850 kg/m3 and viscosity µ=0,8 Pa s is completely filling the spacing h= 2 cm between two parallel horizontal plates of length 2,5 m and width 1 m . The upper plate is pulled at a speed of U while lower plate is fixed . In order to generate a laminar steady incompressible flow of fluid in the spacing at a rate of 0,85 kg/s determine Reynolds Number of flow using the spacing as the characteristic dimension.ANSWER: 2,125 1.C) A fluid of density ρ=850 kg/m3 and viscosity µ=0,8 Pa s is completely filling the spacing h= 2 cm between two parallel horizontal plates of…