For a laminar flow in a circular tube, determine the kinetic energy correction factor a and the a' -r' dp momentum correction factor B, the velocity profile is u = and the average velocity is 4µ dx half of the maximum velocity, the parameters are shown in figure 3.1 Figure 3.1 Cylindrical sleeve element as free body in circular tuber

Q: Water is pumped through a horizontal, smooth circular pipe at a bulk velocity of 0.4 m/s. The pipe…

A:

Q: For water flowing in a pipe of 8 inches diameter at 65 oC and 0.01 ft3/s, what will be the entry…

A: Given: D=8 in=0.2032 mT=65°CQ=0.01 ft3/s=0.0002831685 m3/s

Q: Please answer The test part d and e From this  problem The test is akredytacji solved thank you

A: Since we only answer up to 3 sub-parts, we’ll answer the first 3 parts. Please resubmit the question…

Q: Required information Assume that r = 0.149 m, ro = 0.15 m, µ = 1.49 kg/m-s (glycerin), p = 1260…

A: Calculated the inner shear stress in Pa.

Q: Required information A light liquid (p = 950 kg/m³) flows at an average velocity of 10 m/s through a…

A: Given data :- An average velocity = 10 m/s                        The diameter of tube (d) = 6.6 cm…

Q: What is the volumetric flow rate through at 4 inch (10 cm) diameter pipe containing chocolate milk…

A:

Q: The 100-mm-diameter pipe is connected by a nozzle to a large reservoir of air that is at a…

A: The schematic diagram is,Here, point 2 is the exit point.

Q: QUESTION 9 A liquid cooled heat sink for a smartphone is sketched in Figure Q9. It uses water of…

A: Density ρ= 997 kg/m kinematic viscosity v= 1.19 x 10-6 m2s-1 No of tubes = 5 diameter Dh =5 mm…

Q: Water at 200°C (p = 998 kg/m³, and m2/s flows through a horizontal pipe of diameter with a flowrate…

A: T=200Cρ=998kg/m3v=1×10-6m2/sD=0.1mQ=4×10-2m3/s∆pl=2.59 kPa/m To-Find:- 1. Thickness of viscous…

Q: Problem 4 (category: minor losses, FE prep): Water (density 1000 flows at 1.2 through a system with…

A: problem 4     we have   the water density - 1000 kg/m3  flowing at 1.2 m/s through the system…

Q: Oil (with kinematic viscosity ν = 4x10-5 m2/s and specification SG= 0.9) flows from the upper…

A: Introduction: When fluid flows from one location to another, the head lossless comes into play. The…

Q: Water flows through the following circular pipe with a diameter of 30 mm at a speed of 3 m/s, what…

A:

Q: What is the Reynolds number for a straight and perfectly smooth pipe of length 500 m and diameter…

A: Consider Q is the mass flow rate, ρ is the density of fluid, V is the velocity of the fluid and A is…

Q: b) CHOOSE A SET OF PRIMARY DIMENSIONS c) CHOOSE A SET OF REPEATING PARAMETERS OSE THE REPEATING…

A: (e) dimensionless group Reynolds no = inertia forceviscous force = ρ u Dμ  when Re < 2000 ,…

Q: l Resolving of Example (1-3) Two reservoirs with a difference in elevation of 15 m are connected by…

A:

Q: A shaft with a diameter of D = 80 mm and a length of L = 400 mm, shown in Fig is pulled with a…

A: Given that, Diameter of shaft, D=80 mm,Length of shaft, L=400 mm,Velocity of the shaft, U=5…

Q: A medium sand aquifer 30m thick has two monitoring wells spaced 800m thick along the direction of…

A: Given:To find:(a) Rate of flow per meter of width.(b) Average linear velocity of water.

Fluid Dynamics

The study of the flow of gases and liquids, usually in and around solid surfaces, is known as fluid dynamics in physics and engineering. Fluid dynamics, for example, can be used to evaluate the movement of air through an airplane wing or the surface of a vehicle. It can also be used in ship design to increase the speed at which ships pass through water.