For a laboratory consolidation test on a clay specimen (drained both sides), the following were obtained. Thickness of the clay layer = 25mm o_1 = 200kN/m^2 o'2 = 400KN/m^2 e_1 = 0.73 e_2 = 0.61 Time for 50% consolidation (t_50 = 2.8min: From table U = 50%, Tv = 0.197 Determine the hydraulic conductivity (in cm/sec) of the clay for the loading range.

For a laboratory consolidation test on a clay specimen (drained both sides), the following were obtained. Thickness of the clay layer = 25mm o_1 = 200kN/m^2 o'2 = 400KN/m^2 e_1 = 0.73 e_2 = 0.61 Time for 50% consolidation (t_50 = 2.8min: From table U = 50%, Tv = 0.197 Determine the hydraulic conductivity (in cm/sec) of the clay for the loading range.

Principles of Geotechnical Engineering (MindTap Course List)

9th Edition

ISBN:9781305970939

Author:Braja M. Das, Khaled Sobhan

Publisher:Braja M. Das, Khaled Sobhan

Chapter11: Compressibility Of Soil

Section: Chapter Questions

Problem 11.3P

See similar textbooks

Similar questions

The results of a laboratory consolidation test on a clay specimen are the following. Pressure, ir (lb/ft²) 500 1.000 2.000 4.000 8,000 16.000 Total height of specimen at end of consolidation (in.) 0.6947 0.6850 0.6705 0.6520 0.6358 0.6252 Given the initial height of specimen = 0.748 in.. G specimen = 95.2 g. and area of specimen = 4.91 in.²: a. Plot the e-log or curve = 2.68. mass of dry b. Determine the preconsolidation pressure c. Calculate the compression index, C.
Find the C, and the "apparent" OCR for a superficial clay stratum that is 4m thick. The water is at the surface. A sample of the clay has a water content of 27.9%, and a specific gravity of 2.65. An oedometer test showed the following results: Voids Ratio 0.736 0.733 0.73 0.675 0.638 0.6 Vertical Effective Stress 15 28 60 230 480 930
Problem # 2 Following are the results of a laboratory consolidation test on a sample of undis- turbed clay obtained from the field. Pressure, a' (kg/cm³) Final height of specimen (cm) 2.540 0.5 2.519 1.0 2.5 2.0 2.428 4.0 2.322 8.0 2.206 16.0 2.09 The height of the specimen at the beginning of the test was 25.4 mm, and the diame- ter was 63.5 mm. The moist specimen weighed 140 g and the water content was determined to be 19%. Estimate the compression index and the preconsolidation pressure from the e-log ơ' curve. Given: G, = 2.7. O Cengage Learning 2014
Following are the results of a consolidation test on a sample of undisturbed clay obtained from the field. Pressure ơ' (kN/m²) Final Height of Specimen (mm) 24 10 23.78 20 23.30 50 22.22 100 20.58 200 19.04 400 17.52 800 16.31 17.75 The height of the specimen at the beginning of the test was 24 mm and the area of specimen was 50 cm? volume of specimen was 120 cm³. The mass of dry specimen was 180.4 g. Gs= 2.68. 1. Plot the e-log ơ' curve, 2. Using Casagrande's method, determine the preconsolidation pressure. 3. Calculate the compression index, Cc
‹ample 9.1: Following results were recorded from a consolidation test on a specime turated clay, each load being maintained constant for 24 hours before the addition o ext increment.
8.2
A CU triaxial test was carried out on a silty clay that was isotopically consolidated using a cell pressure of 125 kPa. The following data were obtained: Axial load (kPa) 0 5.5 11.0 24.5 28.5 35.0 50.5 85.0 105.0 120.8 Axial strain, E₁ (%) 0 0.05 0.12 0.29 0.38 0.56 1.08 2.43 4.02 9.15 Au (kPa) 0 4.0 8.6 19.1 29.3 34.8 41.0 49.7 55.8 59.0 (a) Plot the deviatoric stress vs. axial strain and excess porewater pressure vs. axial strain, respectively. (b) Determine the undrained shear strength (su). (Note: we assume that the sample reaches failure). (c) Determine the total principal stresses (0₁,03) and the effective principal stresses (0₁, 03') at the failure, respectively.
During the shearing phase of a CU test, the void ratio of a NC consolidated clay specimen will: 1decrease. 2could increase or decrease. 3remain a constant. 4increase.
2- An undisturbed clay has a preconsolidation pressure of 200 lb/ft. A laboratory consolidation tests yield the following data: o' (lb/ft') e 0.92 3,130 6,270 0.77 a) Determine the void ratio that corresponds to a pressure of 5,800 (Ib/ft). b) Determine the coefficient of volume compressibility for the pressure range stated. c) If C, = 1 x 10* in?/sec, determine hydraulic conductivity, k in in/sec corresponding to the average void ratio within the pressure range.
Question attached
STATEMENTS: A - an increase in volume is expected in 2:1 expanding type of clay when wet/saturated with water. B - cracking is expected when an expanding type of clay dries. A- both statements are trueB- neither statements are trueC- only statement A is true D- only statement B is true
Note) For soil sample in Table 2, initial thickness of sample = 14.31 mm, sample area = 2827.433 mm^2, dry weight measured at the end of test = 52.53 g, specific gravity = 2.7 Also, Determine the compression index and expansion index Please show graph