For a hydraulic power unit, this part protects the pump from taking in any harmful particles that may be in the reservoir

Q: For an 80 gpm pump, what should be the approximate size of the reservoir to ensure sufficient oil…

A: Given data:- pump capacity =80GPM To find:-the approximate size of the reservoir

Q: What happens if the delivery valveof a running reciprocating pump is closed?

A:

Q: Multicylinder pump

A: Where more than one cylinder is being driven by one driver, the arrangement is named according to…

Q: Reciprocating pumps are suitable for high pressures a. False b. True

A: Centrifugal pumps are utilized to actuate flow or raise a fluid from a low level to a tall level.…

Q: how a pump can be a flow measurement device?

A: Flow measurement device is a device that measures the flow rate in pipe. With the help of pump we…

Q: 1-While refilling an 8-quart (7.57 L) system with coolant: Technician A initially puts in 4 quarts…

A: Hi there, Thank you for the question. We’ll answer the first question since we answer only one…

Q: What is the principle of centerifugal pump?

A:

Q: Water is the working fluid in a Rankine cycle. Steam exits the steam generator at 1500 lbf/in.² and…

A: Given data: steam exits the steam generators P5=1500 lbf/in2 and T5= 1100°FThe pressure and…

Q: What is high pressure pump?

A: High-pressure pumps generate a very high pressure of fluid supply. Generally, high-pressure pumps…

Q: The process of filling the liquid into the suction pipe and pump casing upto the level of delivery…

A:

Q: two suggestions in reducing the head loss in the pump and piping syste

A: -Make the surface of the pipe is smooth so that no friction is present in the piping system so this…

Q: What will happen when the pressure at any point inside a centrifugal pump goes below the vapor…

A: Given Data⇒ Centrifugal pump Pressure at any point inside pump Vapour pressure corresponding to the…

Q: ration i

A: given: Methods for treating vibration in pumps

Q: For a hydraulic power unit, this part indicates the amount of oil in the reservoir. Usually, it also…

A: This question is based on the concept of Hydraulic power unit

Q: Which type of the pump is different from others in the same group? Select one: a. Piston pump O b.…

A: We have to find  Which type of the pump is different from others in the same group ?

Q: For a hydraulic power unit, this part reads the oil pressure at the pump outlet

A: This question is based on the concept of Hydraulic power limit.

Q: Which of the following situations will make a pump noisy? Select all that apply. O Excessive oil…

A: Answer:- All given situations will make the pump noisy.   The various situation that will make the…

Q: Which one of the following is a component of a centrifugal compressor? a. Suction valve b. Nozzle…

A: Although the centrifugal compressor is unlikely to be used in gas turbine plants where specific fuel…

Q: Draw the symbol of pressure relief valve and briefly describe about use of the pump and motor?

A: The symbol of simple pressure relief valve is shown below:

Q: For a hydraulic power unit, this part supplies the energy to cause the shaft of the pump to rotate.…

A: Option a is correct.

Q: A pump forms a ___________system A. isolated B. closed C. both open and isolated D. open

A: A pump forms a open system always because both mass as well as energy transfer take place in pumps.

Q: What is the impact on flow and pressure when the impeller of a pump is trimmed? a. Flow decreases…

A:

Q: revolving buoy.  a. venturi meter b. orifice c. pitot tube  d. rotameter

A: Rotameter is used to calculate the revolving buoy

Q: Two types of pumps

A:

Q: A.I) The term pressure drop refers to what in a hydraulic circuit a. The change in the flow rate in…

A:

Q: What part of the circulating system has the maximum pressure drop across it? a. Drill pipe b.…

A: In a circulatory system, drilling fluid goes down through a hollow drilling tool consisting a nozzle…

Q: efine and discuss the important parts of the Duplex Pump.

A: defination a pump with two cylinders especially : one whose plungers are driven directly by the…

Q: What would happen if a hydronic system was installed without an expansion tank? A. The relief valve…

A: The relief valve would constantly go off.

Q: Applications of trash pump

A: Applications of trash pump are -

Q: At the pump's shutoff head, the pump efficiency is maximum. O True O False

A: This question is based on the concept of pump and shut off head.

Q: The total pressure rise in a centrifugal compressor is due to impeller and diffuser action Select…

A: The fluid flowing through the impeller of the centrifugal compressors are imparted kinetic energy…

Q: What is performance characteristics of a centrifugal pump

A: A centrifugal pump is designed to develop certain manometric head and discharge at constant speed…

Q: Which of the following is acting on the fluid in a Vane Pump? a. Centripetal Force b. Centrifugal…

A: A vane pump is a self-priming positive displacement pump that delivers a consistent flow at…

Q: What causes coolant to leak from the water pump weep hole?

A: What causes coolant to leak from the water pump weep hole? Answer: d) A faulty pump shaft seal

Applied Fluid Mechanics

A fluid is a substance that is continuously deformed by the application of shear stress. The rate of deformation of a fluid depends on its viscosity. The fluid tries to flow when it interacts with some other system.