For a given work, minimum possible time under certain condition is 20 mins, most likely time is 32 mins. Assuming work to follow same probability distribution as PERT activity, expected time of work is calculated as 34 mins. Maximum time of work for this under worst condition would be. _mins.

Q: Define the term capillary fringe.

A: The capillary fringe is characterized as the saturated zone of water immediately just above the…

Q: Figure 2.5.3 - Qu Inside perimeter Outside perimeter Centreline

A:

Q: All tapes should be standardised using: Question 17Select one: A. A reference tape   B. A…

A: All tapes should be standardised using:A. A reference tapeB. A baselineC. Both a and bD. A Boning…

Q: Problem 2 Figures on page 3 show the partial framing plan and elevations of a three story steel…

A: Problem -2 Given, Dead load at roof,  DLR=15 psf=15 lb/ft2  Live load at roof, LLR=25 psf=25 lb/ft2…

Q: B1 (12 Wx20 D) 81 (12°Wx200) 2 (12Wx200) 3'-0" 25'-0" 82 (12°Wx20"D) $2 B FLOOR FRAMING PLAN NO…

A: a. floor cross sections will look like this layout:Explanation:  you can input details and materials…

Q: Describe about the Sliding Block Analysis.

A: The sliding block analysis method used by the Newmark is an engineering which determines permanent…

Q: Find the slab thickness for the pand shown Column size - 300*300 -5.00- Jy 350 Mpa -009- 2-5

A: The column size = 300300The yield stress (fy) = 350 MPaTo determine:-The slab thickness

Q: *On the drawing attached, apply a runout requirement to make the left face perpendicular to the…

A: Introduction- Whenever the target is rotating once on the reference axis line, the run-out of the…

Q: 1/ For the plan and section of the wall shown below. Calculate quantities for each of the following…

A:

Q: Given: A square CMU building built using 12"x8"x16" block that is 25'-4" on each side and is 11'-4"…

A:

Q: What is base flow separation?

A: It is required to answer about what is base flow separation?

Q: 4#8 12" 15" I 3: fó= tooopsu Grade Go Steel NWC. &Mn = ?

A:

Q: WOULD THE BEARINGS BE THE SAME?

A: Finding the bearings of a line AB, BC, CD, DA. In above solution find out the azimuth of lines is to…

Q: CONSTRUCT 4 A 4B A SUMMARY TABUL & PLOT Fc = 6000 PS1 fy = 60 ks2 Fe 4000 PS1 Fy = 60 KSI 23 26 14"…

A: Beam AWidth= 14in ; Eff. Depth= 20.5in ; depth of NA= 4.45in ; Strain in concrete= 0.003 ; Strain in…

Q: PROBLEMS, DETERMINE To ALL FOR AFD, SFD, THE AND BMD MAKING SURE SHOW AU WORK REQUIRED To OBTAIN…

A: We will find reactions at A and D and draw FBD to solve

Q: What is a batter board? Boards set across a trench or otherwise placed so as to carry wire or cord…

A: Construction stakeout is the placing of a stake to indicate the location for a pole. Poles must be…

Q: Find the area of all and then convert to square feet

A:

Q: Define the term Underabsorption of Over-Head?

A: Let’s first understand the definition of overhead: Overhead refers to the continuing business…

Q: All are incorrect, can you re-work?

A: The degree of the curve = Da = 5°0' The intersection angle = 20°30' The station of the PI = 63+25.53…

Budget Estimating

The term budget signifies a plan over the long run, generally, a year that covers the financial expenses and revenues of any organization. This budget plan is known to estimate the growth and success of any organization. Civil engineering companies utilize project budgets for estimating project costs, construction costs, and other direct and indirect costs related to the project being undertaken. Project budget is a detailed statistical tool primarily used by project managers to estimate the overall project cost. The project budget is in the form of a document that includes all the costs which are incurred during the project undertaking and after the completion of the project. Large commercial projects have the project budget estimate in the form of large detailed pieces of documents which include every cost estimate regarding man and materials. Labor costs, material procurement costs, construction costs, and operational costs are some of the costs that are incurred during the project execution and planning phase.