Stress (MPa)100080060040020010080604020 |815°C10-6 10-5 10-4650°C730°C925°C-210-3 10-² 10-1 1Steady-state creep rate (h-¹)1010² 10³ For a cylindrical S-590 specimen (Animated Figure 8.33) originally 10 mm in diameter and 516 mm long, what tensile load (in N) isnecessary to produce a total elongation of 2.6 mm after 1600 hours at 815°C? Assume that the sum of instantaneous and primarycreep elongations is 0.81 mm.iN

Given data :- Original diameter = 10 mm Length = 516 mm Total elongation = 2.6 mm Sum of…

Answered: For a cylindrical S-590 specimen…

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Q6/ A material has a true stress -strain curve given by o=Kɛ", derive and calculate the true and engineering ultimate tensile strength of this material. (use : k=689.47kpa , n=0.5)
Determine the single uniformly distributed load in the x direction that would produce the same deformation in the y direction as the original loading for a given rectangular block with the following data: 4 inches long in the x direction, 2.5 inches long in the y direction, and 3.5 inches long in the z direction. The block is subjected to a triaxial loading of three uniformly distributed forces as follows: 52 kips tension in the x direction, 68 kips compression in the y direction, and 49 kips tension in the z direction. Given v = 0.28 and E = 30 x 10° psi, O a. 265.23 kips O b. 255.80 kips Oc 220.25 kips O d. 246.56 kips
Whats the correct answer for this please ?
Two links are connected by a single pin and a tensile force F is applied. The links and the pin are made from Aluminum(sigma_y = 35ksi and T_y = 20ksi). The dimension of the link is 5 inch high by 0.5 inch thick. Find the optimal diameter for the pin and the maximum force,F that can be applied to the linkage before incuring permanent deformation.
3. A rod-shaped MgO specimen with round cross section is tested with the three-point bend method. What is the calculated minimum radius without fracture if the applied load is 5560 N, the flexural strength is 105 MPa, and the separation between the two support pins is 45 mm?
A cylindrical specimen of some metal alloy having an elastic modulus of 101 GPa and an original cross-sectional diameter of 3.9 mm will experience only elastic deformation when a tensile load of 4633 N is applied. Calculate the maximum length of the specimen ( in mm) before deformation if the maximum allowable elongation is 0.31 mm.
What is the maximum value of KIc as per LEFM that can be determined from experiments on a 20 mm thick plate? yield strength= 500 MPa, E= 210 GPa, poission ratio=0.3.
A cylindrical specimen of brass that has a diameter of 15 mm, a tensile modulus of 120 GPa, and a Poisson’s ratio of 0.30 is pulled in tension with force of 50,000 N. If the deformation is totally elastic, what is the approximate strain experienced by the specimen?

Recommended textbooks for you

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Control Systems Engineering

Mechanical Engineering

ISBN:

9781118170519

Author:

Norman S. Nise

Publisher:

WILEY

Mechanics of Materials (MindTap Course List)

Mechanical Engineering

ISBN:

9781337093347

Author:

Barry J. Goodno, James M. Gere

Publisher:

Cengage Learning

Engineering Mechanics: Statics

Mechanical Engineering

ISBN:

9781118807330

Author:

James L. Meriam, L. G. Kraige, J. N. Bolton

Publisher:

WILEY

SEE MORE TEXTBOOKS

For a cylindrical S-590 specimen (Animated Figure 8.33) originally 10 mm in diameter and 516 mm long, what tensile load (in N) is necessary to produce a total elongation of 2.6 mm after 1600 hours at 815°C? Assume that the sum of instantaneous and primary creep elongations is 0.81 mm. i N