Answer would be appreciated For a closed section beam with thinwalls, which of the following optionsis best to give the least twist inresponse to an applied torque?O A large enclosed area with large wallthickness and as small a perimeter aspossible.A small enclosed area, with large wallthickness and as large a perimeter aspossible (ie corrugated shape).O A small enclosed area with small wallthickness and as large a perimeter aspossible (ie corrugated shape).A large enclosed area, with small wallthickness and as small a perimeter aspossible.

Answered: Image /qna-images/answer/ba9e8d46-e7cf-408c-99cd-2db3bdb3d101.jpg

For a closed section beam with thin walls, which of the following options is best to give the least twist in response to an applied torque? A large enclosed area with large wall thickness and as small a perimeter as possible. O A small enclosed area, with large wall thickness and as large a perimeter as possible (ie corrugated shape). A small enclosed area with small wall thickness and as large a perimeter as possible (ie corrugated shape). O A large enclosed area, with small wall thickness and as small a perimeter as possible.

For a closed section beam with thin walls, which of the following options is best to give the least twist in response to an applied torque? A large enclosed area with large wall thickness and as small a perimeter as possible. O A small enclosed area, with large wall thickness and as large a perimeter as possible (ie corrugated shape). A small enclosed area with small wall thickness and as large a perimeter as possible (ie corrugated shape). O A large enclosed area, with small wall thickness and as small a perimeter as possible.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Handwriting not allow please And give me complete answer
We have a rectangular piece. We wish to manufacture a parallel slot along thepiece in a vertical milling machine and 50 cm from the edge. The width of the slot is 40 mm. TheDepth of the slot is 25 mm. For this, several rough cutting steps and aFine cut with a depth of 0.20 mm. The depth for each of the steps ofrough cut is limited to 1.75 mmAditional information:What is the number of blades used for the rough cutting steps?What is the number of blades used for the fine cutting step?
Question 4 a) Each cylinder in a four-cylinder car engine has a bore diameter of 63.53 mm and the stroke for each piston is 175.00 mm. Calculate the cubic capacity of the engine in cm? and calculate the clearance volume per cylinder for a compression ratio, r, of 6.25. b) The bore diameter of each cylinder in a six-cylinder four-stroke internal combustion engine is 32 mm and the stroke of each piston is 125 mm. During testing., the engine runs at 1450 revolutions per minute (rpm) with a pressure-volume indicator diagram showing a mean net area of 2.90 cm and a diagram length of 0.85 cm. The pressure scale on the indicator diagram is set to 165 kN/m per cm. Calculate the mean effective pressure (m.e.p) and the indicated power in kilowatts (kW) developed by this six-cylinder four-stroke engine. Give your answer to 2 decimal c) A hollow connecting rod has an inner diameter of 26.25 mm and is subjected to an axial tensile load of 500 MN. If the maximum allowable stress for this hollow rod…
Hello ! I hope you are well.Why are we taking this specific cross section for the second part of the question ? Is it because it's the one where the nails are ?
Power is supplied at the rate of 0.40 hp for 2 min in drilling a hole in a 1.0 lb brass block. (a) How much heat is generated? (b) What is the rise in temperature of the brass if 75% of the heat generated warms the brass? What happens to the other 25%? (don't change the hp, lb)
1. Define manufacturing processes, design engineer, industrial engineer and materials engineer? 2. Name and explain a protess to make cylinder shaft? 3. Discus at least three factors which will effect tool life? 4. Define finishing and roughing process? 5. Explain the negative effect of heat generated from machining process? 6. One limitation of sand casting is bad surface finish. Yes or No? Why? 7. What is permeability in casting process? 8. What are the major defects in casting process? 9. Which type of casting process should be use for high melting point casting, such as cast iron and why? 10. Casting problem A certain mold has a sprue whose length is 20 cm and the cross-sectional area at the base of the sprue is 2.5 cm?. The sprue feeds a horizontal runner leading into a mold cavity whose volume is 1560 cm³. Determine: (a) velocity of the molten metal at the base of the sprue, (b) volume rate of flow, and (c) time to fill the mold (in second). mfg m1 Spring 2020 999.pptx
Solution 1: Ergonomic Assessment and Improvement. An ergonomic assessment of Paula's workstation could identify areas where adjustments could be made to reduce strain on her wrists. This could include adjusting the height of the workstation, providing wrist supports, or changing the design of the tools she uses. The strength of this solution is that it directly addresses the physical strain causing Paula's discomfort. However, the weakness is that it may require investment in new equipment or tools, and the effectiveness will depend on the specific changes made. Solution 2: Job Rotation. Paula could be rotated between different tasks more frequently, reducing the amount of time she spends on tasks that strain her wrists. This could also include training other workers to perform the welding and gaging operations, allowing for more flexibility in task assignments. The strength of this solution is that it reduces the repetitive strain on Paula's wrists. The weakness is that it requires…