For a class B amplifier using a supply of VCC = 100 V and driving a load of 1.7 kilo ohm, determine the maximum input power, maximum output power, maximum circuit efficiency and the maximum transistor dissipation by each transistor. max Pi = 3.74watts, max Po= 3.75 watts, max effic = 75%, max Pq = 0.85 watts. max Pi = 3.74watts, max Po = 12.94 watts, max effic = 79.6%, max Pq = 0.9 watts. max Pi = 5.74watts, max Po= 1.94 watts, max effic = 78.6%, max Pq = 0.49 watts. O max Pi = 3.74watts, max Po = 2.94 watts, max effic = 78.6%, max Pq = 0.596 watts.

For a class B amplifier using a supply of VCC = 100 V and driving a load of 1.7 kilo ohm, determine the maximum input power, maximum output power, maximum circuit efficiency and the maximum transistor dissipation by each transistor. max Pi = 3.74watts, max Po= 3.75 watts, max effic = 75%, max Pq = 0.85 watts. max Pi = 3.74watts, max Po = 12.94 watts, max effic = 79.6%, max Pq = 0.9 watts. max Pi = 5.74watts, max Po= 1.94 watts, max effic = 78.6%, max Pq = 0.49 watts. O max Pi = 3.74watts, max Po = 2.94 watts, max effic = 78.6%, max Pq = 0.596 watts.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Determine Vx and the mode of operation of the PNP transistor shown in the figure below. Assume Is = °A, B = 50, VA = 00, and Rc = 0.1 KO. 10x10-16 %3D Vcc는 2 V 1.2 V- Rc Select one: a. 0.577 V, Active Mode O b. 0.23 V, Active Mode O c. None of these d. 1.153 V, Active Mode e. 2.306 V, Saturation Mode
34
Elecronics Engineering
answer part b,c, and d
The maximum junction temperature of a transistor is 150°C and the ambient temperature is 25°C. If the total thermal impedance is 1°C/W, what is the maximum power dissipation ?
Use 2 decimal places A CS JFET amplifier has gm= 6.82 mS, with a drain resistance of 1.13 kohms and load resistance of 685.52 ohms. Voltage gain (absolute value) is Round your answer to 2 decimal places.
QUESTION 5 Given is the principle diagram of a regulated power supply shown below. Reference voltage VREF Error amplifier 21 Series-pass transistors 22 www R₁ R₂ -ovo Assume that R₁ = 10K, R₂=4.7K and VREF=5.6V. Determine Vo in Volt and write your answer without the unit.
4. A Darlington transistor is essentially an array of two transistors connected as shown below. Assume both transistors follow our simple model with a current gain of B=100. Determine the maximum value of R2 that will just saturate the transistors, and pass full current through the load resistance R1. v2 V2 R2 PULSE (0 5 0) Q2 NPN R1 10 Q1 NPN V1 24
Which of the following is the basic feature of the emitter-connected amplifier circuit? I. It has voltage gain II. It has current gain III. There is a 180 degree phase difference between the input signal and the output signal
The operating point of the npn transistor is defined by a couple of values: Icand Ver- Select one: OTrue O False In the following figure. Q, and Q: are identicaland operate in active mode. if la =9 Icz then V,V2 IC
Q3 Figure 3 shows two current mirrors based on MOSFET. Derive a formula relating the input current Iin to the output current Iout for the current mirror on the left of Figure 3 stating any assumption. (a) (b) Derive the input resistance Rin and output resistance Rout for the circuit on the left of Figure 3. State any assumption. (c) Derive a formula relating lin and Iout for the circuit on the right of Figure 3 assuming that M1 and M2 are identical, and that the length and width of the channel for the transistor M4 are double respect to those of M3. State anv assumption. VDD M3 M4 out Iout M1 M2 M1 M2 Vss = 0 V Vss = 0 V Figure 3
For the given Common Emitter NPN Amplifier, the transistor made of Germanium diodes, BDC-80, Vcc Rc-3.9 K2, RE-0.68 KQ. a) Name the type of biasing used in the above circuit? 1 = 16 volts, R= 62 KQ, Rz 9.1 K R, Rc Cs b) Find VE? Find VCE? d) Find Vc? e) What is the name of the capacitors C1, C3 and C2?