if you can solve this thank you! Flux density, B esla13Siliconsheet steel1.211100.9080.70605Cast steel0403Cast iron0.20.1200400Field intensity,$00 800 1000(At/m)FIGURE 1.7Magnetization600 Consider the magnetic core shown in the figure and notice that three sides of the core areof uniform width, whereas the forth side is somewhat thinner. The depth of the core intothe page is 10 cm and the coil has 300 turns. Determine the current that will produce 5.0mwb flux in the core. Use the cast steel magnetization curve of figure 1-7 of Sentextbook.10cmT10cm20cm20cm 州5cm10cm

Step 1: Step 2: Step 3: Step 4:

Answered: Flux density, B esla 13 Silicon sheet…

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter7: Symmetrical Faults

Section: Chapter Questions

Problem 7.21MCQ

See similar textbooks

Similar questions

22. The voltage applied to the h.v. side of a trans- former during short-circuit test is 2% of its rated of voltage. The core loss will be........percent the rated core loss. (a) 4 (b) 0.4 (c) 0.25 (d) 0.04
A transformer has primary and secondary turns of 1250 and 125 respectively. It has core cross-sectionof 36 cm2 and its rms flux density is to be limited to 1.4 T (to prevent core saturation). Whatmaximum 50 Hz voltage can be applied on the primary side and the corresponding open-circuitsecondary voltage?The core has a mean length of 150 cm and its relative permeability can be assumed to be 8000. Whatwould be the rms exciting current when the transformer’s primary winding is excited at a voltage ascalculated above? Also calculate the magnetizing susceptance as seen from primary and secondarysides.If the transformer were to be excited at 60 Hz, 1. What should be the maximum primary voltage for thecore flux density limit not to be exceeded? 2. What would be the magnetizing susceptance as seen oneach side in this case?
Full calculation with any assumption needed. All sub questions please as it is all related.
a core type transforem is constructed with 0.014-in. thick laminations having a uniform width of 2.75 in. If the maximum flux and flux density are, respectively, 6.2 X 10' maxwells and 8.2 X 10 maxwells per square inch and the air spaces between laminations occupy 8 per cent of the stacked core, calculate the number of laminations in the transformer. I
Amagnetic field is being generated by a current of 2.0A flowing through 180 turns of wire on a core having a reluctance of 210000.0 At/Wb. Determine the flux of the circuit in mWb.
(a) Explain briefly what is fringing effect and leakage flux. (b) A ferromagnetic core is shown in Figure 1. The depth of the core is 10 cm. The other dimensions of the core are as shown in the figure. By assuming the magnetic leakage to be negligible and relative permeability of the core is 800. Calculate the total reluctance and find the value of the current that will produce a flux of 0.01 Wb. With this current, calculate the flux density at the top of the core 20 cm 40 cm 10 cm, 30 cm 500 turns 30 cm 30 cm Figure 1
The core of a transformer operating at 50 Hz has an eddy current loss of 100 W/m3 and the corelaminations have a thickness of 0.50 mm. The core is redesigned so as to operate with the same eddycurrent loss but at a different voltage and at a frequency of 250 Hz. Assuming that at the new voltage themaximum flux density is one-third of its original value and the resistivity of the core remains unaltered,determine the necessary new thickness of the laminations. Clear and detailed solution.
Consider a ferromagnetic ring (nucleus) that has a mean circumference of 40 cm, 300coiled copper turns and a sectional area of 5 cm2. A current of 2 is appliedA to winding, producing a flux of 1.5 mWb.Determine the permeability of the core material.Determine the relative permeability of the core material.If the ferromagnetic ring has an air gap of 2 mm. Find the required MMFso that the flux density in the gap is 0.5 T.
I need the answer at 20 minute
A. Describe the characteristics of amorphous iron that make it suitable for integrated transformer applications. B. What are the key techniques for the fabrication of high quality amorphous materials in general?
Q1. Describe the following related to Current Transformer (CT): (i) Draw the equivalent circuit diagram of CT and develop the corresponding phasor diagram. Draw the transient response of CT and describe the transient errors in a CT. [5] [5] (ii)
Q.4/ choose true or false: 1. The reluctance of any core is proportional directly with the length of it and inversely with both the permeability and the cross-section area of it. 2. The number of parallel paths in wave windings is equal to twice of the number of poles. 3. In dc machines with same values of Z, N, Ø, the emf for wave winding type is more than emf of lab winding type. 4. If we insert a current in such a conductor subjected to a constant magnetic field, a movement will achieved giving the principle of electric generator.

SEE MORE QUESTIONS

Recommended textbooks for you

Power System Analysis and Design (MindTap Course …

Electrical Engineering

ISBN:

9781305632134

Author:

J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:

Cengage Learning

Electric Motor Control

Electrical Engineering

ISBN:

9781133702818

Author:

Herman

Publisher:

CENGAGE L

Power System Analysis and Design (MindTap Course …

Electrical Engineering

ISBN:

9781305632134

Author:

J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:

Cengage Learning

Electric Motor Control

Electrical Engineering

ISBN:

9781133702818

Author:

Herman

Publisher:

CENGAGE L

SEE MORE TEXTBOOKS