fluid mechanics A pipe 200 (mm) diameter carries Oil at a flow rate of 0.030 (m³/s). The pipe diameter reduces from 200 (mm) to 150 (mm). Point 1 is located at the beginning of the pipe and point 2 is located at the end of the pipe. Elevation of point 1 is 165 (m) lower than elevation of point 2. Water pressure at point 2 is atmospheric pressure. Water flow in the pipe ascending from point 1 to point 2. Total head losses of flow in the pipe equals to 15 (m). 1- Find the value of pressure head of Oil at point 1. 2- Draw the H.G.L. of flow in the pipe.

fluid mechanics A pipe 200 (mm) diameter carries Oil at a flow rate of 0.030 (m³/s). The pipe diameter reduces from 200 (mm) to 150 (mm). Point 1 is located at the beginning of the pipe and point 2 is located at the end of the pipe. Elevation of point 1 is 165 (m) lower than elevation of point 2. Water pressure at point 2 is atmospheric pressure. Water flow in the pipe ascending from point 1 to point 2. Total head losses of flow in the pipe equals to 15 (m). 1- Find the value of pressure head of Oil at point 1. 2- Draw the H.G.L. of flow in the pipe.

Name: fluid mechanicsA pipe 200 (mm) diameter carries Oil at aflow rate of
Uploaded: 2024-03-20T06:56:55.000Z
Channel: Bartleby
Description: fluid mechanicsA pipe 200 (mm) diameter carries Oil at aflow rate of 0.030 (m³/s). The pipediameter reduces from 200 (mm) to 150(mm). Point 1 is located at the beginningof the pipe and point 2 is located at the endof the pipe. Elevation of point 1 i

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Water flows through a pipe at a velocity of 1 m/s. The pipe has a relative roughness of 0.001 and has a diameter of 100 mm. 1. Using the information provided above and in the Moody diagram, drag and drop circle labelled "1" (located below the graph) where the corresponding Reynolds number and relative roughness intersed 2. Drag and drop circle labelled "2" to the point on the y axis where you would read off the friction factor (f). v = 10-6 m²/s for H20 at 20°C. V.1V aminar.Critical low 0.09 zonc Transition zone 0.08 Complete turbulence, rough pipes 0.07 0.05 0.04 0.06 0.03 0.05 0.02 0.015 0.04 0.01 0.008 0.006 0.03 Res 0.004 0.025 0.002 0.001 0.0008 0.0006 0.0004 0.02 Smooth piper 0.015 0.0002 0.0001 0.000,05 0.01 0.009 0.000,01 10' 2(10) 3 4 56 8104 2(10) 3 4 56 S105 2(10) 3 4 56 $106 2(10) 3 4 56 S102(10) ³¸ 4 56 $10 0.008 Vd Reynolds number Re= -0.000,001 -0.000,005 Friction factor f= Relati ve roughness
Water flows through a horizontal pipe of cross sectional of 20 cm2. Atone section, the cross sectional area is 4 cm2. the pressure difference is29.4 psi. How many cubic meters of water will flow out of the pipe in 1min? (can you show the diagram or illustration if possible. thank you!) Choices: a. 0.008 b. 1.208 c. 0.493 d. 0.0185
A Newtonian fluid with absolute viscosity (Greek mu) flows past a flat surface. Due to the no-slip boundary condition, the velocity profile, u(y), develops near the surface and is given by u/U (shown in image provided) where the constant parameters U and delta have dimensions of velocity and length respectively.a) Develop an expression for the shear stress acting in any horizontal plane.b) Determine the shear stress acting on the surface at y = 0 and again at the edge of the boundarylayer, y = delta. (Express your answers in terms of Greek mu, the outer velocity U, and the boundary layer thickness delta.)
Completely solve and box the final answers. Write legibly 9. A blower with the inlet open to the atmosphere delivers 250 cubic meters per minute of air at a pressure of 2.50 cm of water gage through a duct 25 cm in diameter, the manometer being attached to the discharge duct at the blower. Air temperature is 25 degrees C and the barometer pressure reads 1.025 bar. Calculate the required motor rating in KW if the blower efficiency is 92.5%
A1) Floodgates, also known as stop gates, are adjustable gates that restrict the flow of water in flood barriers, reservoirs, rivers, and stream systems. Floodgates prevent river water from backing up into cities during high water levels. 5 m 160° B Figure 1: Floodgate As an aerospace engineer with a solid foundation in fluid mechanics, you would like to propose a temporary design solution to mitigate the damage or disruption of a nearby airport runway flood. The floodgate is 3 m wide and 5 m long, with a solid gate (AB) hinged at point B and restrained by a force-pulley mechanism at point A. The value of mass P is 2500 kg. Assume the density of water is 1000 kg/m. a) Draw the free body diagram of the floodgates system. b) Calculate the depth of water assuming this rectangular gate is in equilibrium, ignoring the weight of the gate. c) Repeat the calculation as in (a), including the weight of the 5-cm-thick steel (SG = 7.8) gate. d) Suppose the length of the gate AB is doubled; what…
Q1) By using dimensional analysis concept, express the wall shear stress for the pipe flow which is depending likely on the distance from the beginning of the pipe, pipe diameter, pipe wall roughness, fluid velocity, density and viscosity?
Q3. Referring to the jet-impact test shown in Figure 3: The following tables show one measurement for the 90o-deflection plate. Referring to the lab manual, complete the missing columns in the tables.
A Pitot-static probe was used to measure the velocity distribution in a water tunnel. The two pressure lines from the probe were connected to a U-tube manometer which uses a liquid of specific gravity 1.7. The maximum velocity expected in the water tunnel was 2.3 m/s. Your job was to select an appropriate U-tube from a manufacturer which supplies manometers of different heights. The cost increases significantly with manometer height. Which of these should you purchase?
subject (fluid mechanic 2) pls show me full steps with clear handritin sir pls answer me within 30 min sir
Shown below is a performance data for a water pump. For each row of data, calculate the pump efficiency (percent). Estimate the best efficiency point (%) and the volume flow rate (gpm) and net head (ft) at the best efficiency point. gpm ft KW 200 75 4.9 300 73 6.7 400 71 7.2 500 66 8.1 600 60 9.0
Please solve! Find the air horsepower of an industrial fan that delivers 55 000 cubic feet of air per minute through a 3 ft. by 4 ft.; pressure is 5 in. of water; air temperature is 700 F and barometric pressure is 29.92 in. of mercury.
The figure shows a system in which water flows from a tank through a system of pipes that have various sizes and heights Determine: a) The gauge pressure at points A, B, C, D, E, F, G. b) The velocity at points A, B, C, D, E, F, G. c) Construct a diagram showing the line of total energy (L.E) and the line of mechanical height (L.A.M)