نقطة واحدة Flow of air through a tapering-10 * pipe is steady uniform unsteady non-uniform steady non-uniform none of these O

Q: Based on the system shown in Figure 1, develop the position equations from your fixed datum lines,…

A:

Q: resolve solution

A:

Q: Consider the equation for angular twist due to torsion. Imagine you are designing a solid round…

A: The angular distortion of an item caused by a couple of twisting torques is known as the angle of…

Q: A bcc (111) surface has the following (3x1) adsorbate structure: Select all of the following LEED…

A: Solution: Given Data:

Q: QI Define five of the following with sketch. 1-Taper turning 2- Light alloys 3- AA2024 4- Rolling 5-…

A: Taper turning is a turning technique in which the cutting tool travels at an angle to the…

Q: solve both

A: Power input, Gear speed of input shaft, Gear ratio, Power loss,

Q: (b) Compute the internal torque exerted on gear A (TAC), gear C(TcD) and gear D (TDB). (c) Sketch…

A:

Q: For the frame shown below, Is supported by pins at C and D. Determine the magnitude of reaction at C…

A: Consider the free body diagram of the member CBA as shown below.

Q: What is the maximum magnitude of the bending moment caused by force G? If none, enter zero. Do not…

A: It is required to determine the magnitude of the maximum bending moment by the force G.

Q: 3. both wires is identical at 1.5 meters and both wires are 5 mm in diameter. The steel wire is made…

A:

Q: дл др Os ӘТ S Cp

A: Write the expression at constant enthalpy. dh=Tds+vdP0=Tds+vdP∂s∂ph=-vT

Q: ) The disk is rotating about point O with an angular velocity x=7 rad/s in the given direction. Rod…

A: Given Data: The angular velocity of the disc is ωo=7 rad/s. The value of other variables are r=4 m,…

Q: solve frist one please

A: The diametral pitch of each gear:center distance of the gears:Velocity ratio:

Q: You are designing a new engine; this device operates with liquid fuel as an input and gener energy…

A: Hello. Since you have posted multiple questions we will solve the first question for you. If you…

Q: (4) 8.8.8.8 16 8 8 16 21

A: the question is not fully asked   bricks and blocks are given

Q: 200 mm В

A:

Q: D raio s.f.D and B.M.

A:

Q: The assembly consists of a 3-kg vertical pulley A and a 14 horizontal pulley B. If a 2-kg block is…

A: Given data: m=3 kgM=14 kgr=30 mmR=100 mmh=0.1 m Need to determine the speed of pulley B.

Q: Q1: Find the angle of the force? 250 Ib 110 Ib 25 140 Ibk 40° 90 Ib 170 Ib

A:

Q: As shown, a section of a roller coaster track (Eigure 3) follows the form of y = (2/3)x¹.5 Locate…

A:

Q: ENTIRE ANSWER IS WRONG

A: Initial velocityFinal velocityInitial angleFinal angleWeight of the basketball

Q: Using the method of joints, determine the force in each member of the truss shown. State whether…

A:

Q: Given : Mass of Gears A and B = 2.4 kgs Mass of Gear C = 12 kgs Gears A and B's radius of gyration =…

A:

Q: Choose three types of Reuleaux lower pairs, and answer the following, F.1 Write down their names?…

A:

Q: Incorrect please resolve both parta

A: To calculate the surface temperature of the tank when it is passed through water and to calculate…

Q: In this case, the applied force is always pulls upward, but the amount of force that can be applied…

A: According to the given data  We need to find The true statement

Q: If a = 9 in., locate the distance to the centroid of the member's cross-sectional area. (Figure 1)…

A: Draw the given diagram.

Q: Calculate the number of degrees of freedom The value must be a number 11 Calculate the number of…

A: Full joint is the joint which has area or surface contact, and half joint is the joint which has…

Q: A) Are all the nodes in the same plane?. B) To the surface, what would the unit of perpendicular…

A: The 3 dimensional geometric coordinates of the system are taken in uniform units as millimetre. They…

Q: How did you get the value of "F"

A:

Q: What is the normal force applied to the block?

A:

Q: At a given moment four link mechanism OABO, is in the position shown on the figure and OA= AB = AO =…

A:

Q: Through the two pipes in Figure 6 flow equal flows of water. data: Pipe diameter No. 1: 200 mm -…

A:

Q: The brake piston consists of a full cecular part. Its cross section is shown in ( Eigure 1). Suppose…

A: Cross-section:a=18 mmb=80 mmc=55 mmd=35 mme=30 mmf=45 mmTo determine: interior surface area of brake…

Q: The point 1/4 of the way from (1,-3, 1) to (7,9, –9) is A. (4,3,-4) O B. (3/2,3,-3/2) OC.…

A: A point's coordinates are a pair of integers that define its precise position on a two-dimensional…

Q: Starting from rest, Block A moves down the inclined plane with velocity given by 3t“, where t is in…

A:

Q: why is F3 0

A: Hydrostatic Force- A resultant force which acts on a submerged surface due to the pressure loading…

Buckling of columns

The column is described as a vertical member of the structure that carries an axial compressive load, and buckling is a lateral deformation of the column under the application of load.