Five sources, each with a bit rate of 1000 kbps are to be combined using synchronous TDM. Each output slot carries 1 bit from each source. What is the frame size?

Q: Q23/ The bandwidth for an FSK signal with a mark frequency of 32 kHz, a space frequency of 24 kHz,…

A: Mark frequency = 32 kHz Space frequency = 24 kHz Bit rate = 4 bps

Q: 2. (b) Suppose, a synchronous TDM multiplexer combines 5 sources and sends only TWO characters from…

A: Answer: I have given answered in the handwritten format in brief explanation

Q: The difference between SLA and HDD is as follows:

A: Service level agreements or SLAs, are a sort of agreement between two gatherings. It's a composed…

Q: 2- The FM modulator has k 30 kHz/V modulated with frequency deviation =127.2khz . Calculate the rms?

A:

Q: A certain number of data bits (D) are encoded by a single pulse in one of 2D possible positions…

A: Answer: c PPM

Q: I need a term for the sum of the rotational delay and the seek time.

A: Rotational delay and seek time: Rotational delay is the amount of time it takes for a track sector…

Q: 3. What is the minimum number of bits required to have resolution 0.5 psi or better given a pressure…

A: Here we require a resolution of 0.5 psi over a range of 0 to 100 psi, i.e. 0.5% The resolution of a…

Q: 4. There are four sources, each creating 500 characters per second. If the interleaved unit is a…

A: Data rate :  Data Rate is the  as the amount of data transmitted during a specified time period over…

Q: The VGA specifications give the following details for the parts of a single horizontal scan: Active…

A: The objective of the question is to calculate the total time for a complete horizontal scan line,…

Q: In a multi mode optical fiber, the propagation of beams is almost horizontal Select one: O True O…

A: Multimode optical fibre uses larger core .

Q: (2) In asynchronous transmission, why do we keep the number of data bits between the start bit and…

A: The start and stop bits are used in asynchronous communication as a means of timing or synchronizing…

Q: A binary signal is transmitted using Angle modulation. You are located at the receiver and you…

A: Answer: In frequency modulation (FM), the carrier signal's frequency varies in response to the…

Q: The multiplexing technique that includes the use of several light signals is: Select one: A. WDM…

A: Given Question: To choose the correct option.

Q: The average signal rate of 2BlQ is a. N b. N/2 c. N/4 d. N/6

A: Question The average signal rate of 2BlQ is a. N b. N/2 c. N/4 d. N/6

Q: 2. To convert an analog signal, with bandwidth 2 MHz, to digital signal the sampling frequency Is…

A: We need to find the sampling frequency.

Q: If a MicroBit requires taking 68ms to do analog-to-digital conversion and 32ms to calculate and…

A: As per the question the maximum sampling frequency is calculated as fm= (68*5)/32 = 10.62 and then…

Q: Write MATLAB codes to draw the following signal within the given limit of x-axis. x60 + + -1.0 -0.5…

A: Dear Student, The required source code, implementation and expected output of your question is given…

Q: Q. Determine the binary output code of a 3-bit flash ADC for the analog input signal in figure…

A: I WILL GIVE THE HANDWRITTEN SOLUTION

Q: Find the minimum output bi shown below. The inputs to first-stage mux are all 1 Kbp

A: The answer is given below:

Q: andwidth of the light for the following wavelength ranges (assume a propagation speed of 2x108…

A: Assume a propagation speed of 2x108 m/sec 1000 to 1200 nm 1000 to 1400 nm

Q: Assume that the 60-dB bandwidth of a receiver is 12 kHz and the 6-dB bandwidth is 7 kHz. What is the…

A: Given : 60 dB Bandwidth of a receiver = 12 kHz 6 dB Bandwidth of a receiver = 7 kHz We need to…

Q: For BPSK modulator fc= 70Mhz, input bit rate 10Mbps.Determine Upper and lower frequency? baud rate?…

A: Given Data

Q: Construct a 4-to-16-line decoder with five 2-to-4-line decoders with enable.

A: A 4 to 16 line decoder contains : 4 input lines and 16 output lines(which are combinations of all 4…

Q: Circular polarization involves critical alignment between transmitting and receiving antenna. A.…

A:

Q: Assume that a system has two potentiometers that are to ADC channels S and 11 respectively,…

A: 1. Calculate the value of AD1PCFG registerAnswer: 0xFFF0 will be the value of AD1PCFG registerSince…

Q: If data bits are transmitted serially at a 1 MHz rate, how many bits can be transmitted in 1 ms?

A: The data rate can be measured in terms of bits per second. It implies the number of bits transmitted…

Q: 1. (a) What is Frame Synchronization in TDM technique? Why are guard bands used in FDM and are not…

A: Frame Synchronization in TDM technique: TDM frameworks, it is significant not just that an edge must…

Q: difference between the si

A: given - In terms of the CE signal, what is the difference between the single-byte and burst modes?

Q: Write a program for the MSP-430 FR 6989 Eval board with the attached IR-board that broadcasts a…

A: This program can be defined in such a way that it will first configure the IR LED pin as an output…