First, design a beam and obtain its moment and bending stress diagrams using the software BeamBoy. The beam has the following specifications: · Length 8 m · Simply supported at 0 m and 6 m · There is a uniform distributed load of 10 kN/m between the two supports · There is a point load of 20 kN located at the end of the beam · When using BeamBoy, select the cross-section W12 × 96

First, design a beam and obtain its moment and bending stress diagrams using the software BeamBoy. The beam has the following specifications: · Length 8 m · Simply supported at 0 m and 6 m · There is a uniform distributed load of 10 kN/m between the two supports · There is a point load of 20 kN located at the end of the beam · When using BeamBoy, select the cross-section W12 × 96

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

The steel beam has the cross section shown. The beam length is L = 4.2 m, and the cross-sectional dimensions are d = 360 mm, bf = 180 mm, tf = 16 mm, and tw = 6 mm. Calculate the largest intensity of distributed load w0 that can be supported by this beam if the allowable bending stress is 210 MPa.
9. A steel portal frame has dimensions, plastic moment capacities and applied loads as shown in the figure. The vertical load is always twice of the horizontal load. The collapse load P required for the development of a beam mechanism is P A B Mp K 2P 2Mp L с Mp D L
Analyze the longitudinal schematic diagram of the metal beam shown, taking into account the support conditions, loads and dimensions presented. This diagram was idealized by taking important data from the real situation in the field. The cross section of the beam is rectangular, with a width of b = 80 mm and a height of h = 320 mm. First, find the Maximum Normal Stresses (Tension and Compression) and the Maximum Shear Stresses, showing where they occur (both longitudinally and transversely). Next, find the Normal Stress and Shear Stress at a point 200 mm above the base of the beam and 0.5 m from the left support. Compare your results to the Ultimate Stress or Yield Stress of a material and comment.
Calculate deflection of bd
Current Attempt in Progress The cantilever beam consists of a rectangular structural steel tube shape [E = 29,000 ksi; = 1990 in."). For the loading shown, determine: (a) the beam deflection at point A. (b) the beam deflection at point B. Assume MA= 250 kip-ft, P= 14 kips, LAB = 4.1 ft, LBc = 6.2 ft. MA LAB LBC Answer: in. (a) VA- in. (b) VB - 4. Submi Attempts: 0 of 1 used Save for Later
The cantilever beam consists of a rectangular structural steel tube shape [E = 29,000 ksi; / = 1990 in.“]. For the loading shown determine: (a) the beam deflection at point A. (b) the beam deflection at point B. Assume MA = 150 kip-ft, P = 30 kips, LAB = 4.9 ft, LBc = 7.4 ft. MA A B LAB LBC Answer: (a) VA = in. (b) VB = in.
Only ?% correct solution
A double tee cross section is used for the beam shown below. Assume the following lengths and loads: a = 15 ft b = 8 ft C= 10 ft P= 12500 Ib Q= 5000 lb The moment of inertia of the cross section is i, = 110 in.". Determine the magnitude (ie, the absolute value) of the maximum compressive bending stress in the beam. TT 3.2 in. B D 5,8 in. Answer: Omax (Compression) = 1 psi %3D
Design the diameter of the pin for the hinge support if the allowable shear stress is 250 MPa. *DRAW THE FREE BODY DIAGRAM *COMPLETE SOLUTION *3 decimal places ALL ANSWER