Find the weight W in the given figure to cause impending motion of the weight W down the plane if the coefficient of friction is 0.29 for all surfaces. Consider the pulley frictionless. * 500 N T1 T1 W 30° 15°

Q: 1. A cylindrical container gromm in diameter, 2 meters long is to be filled with methane gas, 16°C.…

A: Dear student,                     According to the guidelines, I am allowed to answer only one…

Q: Write the derivation of Conversion formula Temperature unit ⁰Re or Réaumur

A: Suppose there are four identical thermometers. Which are then submerged in the boiling water.…

Q: 12-34. Design a cylindrical tank for compressed natural gas at a pres- sure of 4.20 MPa. The minimum…

A: The pressure is The minimum inside diameter is The factor safety is The cylinder material is…

Q: A 4.8 m long from fixed point, 0.5 m wide and assumed a thickness of 30 mm throughout a springboard…

A: “Since you have posted a question with multiple sub parts, we will provide the solution only to the…

Q: Cast iron is used to make rollers as it has superior compression load. Select one: True False

A: Solution:

Q: What functional problem results from torsion?

A: Given:What functional problem results from torsion?

Q: Exus S.fd and Bomid? Draw YKN/m AX=0, 3m

A:

Q: Shown below is a figure of a landing gear configuration on the VS and VD planes (for landing gear…

A: The given figure shows the landing gear configuration on the VS and VD planes (for landing gear the…

Q: A steel shaft transmits 50 Bhp at 1400 rpm. Find the torque in in-lb.

A: Given data: PB=50 hpN=1400 rpm Need to determine the torque in in.lb.

Q: has part B of this problem been done

A: using the Euler's first law for rotation, the reaction force at each bearing is,

Q: A faxe 5kN opblied 1SKN on Hod a°cirular sechonal Detrimine dtress snas area SmmL. of

A: Given data :Load (P)=5 KNArea (A)=5 mm2

Q: Q4: A/Compare between single package and split type

A: Comparision between single package and split type

Q: 02: The figure below shows 3 flange coupling tei. UW Kycrs JP generator delivers power cf 10 HP and…

A: Given DataP=10HP=70×746=7460wattN=1500rpm ***As per our company policy we are supposed to only 1…

Q: Mechanical services , i need solutions in 10 minutes please. MCQ/The heat transfer due to solar…

A: Given data⇒ Heat transfer due to solar radiation through the window

Q: Convert to cis form

A: Conversion to cis form.

Q: A cubical furnace 0.5m x 0.5m x 0.5m on the inside is constructed of fire brick(k = 1.04W/mK) with…

A:

Q: What will be the occerelalion at point L if theuniform KL bor is left horigontal. 2m Support…

A: Given, The mass of the bar, m=25 kg The length of the bar, L=4 m

Q: Q2/ Compute the burst-pressure rating for 10.75-in., J-55 casing having a nominal wall thickness of…

A: The burst pressure rating is 3581.4 psi.

Q: -d12 The figure shows a tabletop experi- nent that can be used to determine an unknown homent of…

A:

Q: A 10' C B 10' E 10' 10' 20 kips 20 kips 20 kips H vy K M 10' 10' 20 kips 20 kips 20 kips 10' N 15'…

A:

Q: The task is to utilise ANSYS Workbench in the design and simulation of a linear, open-sidedcovered…

A: Step 1:Step 2:Step 3: Step 4:

Q: metaicfhread: Pitch- 3mm thocadaryle=65 using 3-wire meltad Best size wisre diametoe ?

A:

Q: Please solve ellaborately and include the untis in every step, show diagram and write your solutions…

A:

Q: Nou Conformance t found wwle to paodu withim the po in Stiu r per

A: Given Data⇒ Product Cost

Q: A steel drum of a lifting machine has a mass of 25 kg, 2.4 m in diameter and 0.20 adius of gyration.…

A:

Q: 1. The assembly consists of two sections of galvanized steel pipe connected together using a…

A:

Q: Are constant-load spring mounts lower cost than variable-load ones, considering the same range of…

A: The constant load spring is designed to use in case of constant load whereas the variable load…

Q: I need these three parts answered pertaining to the print provided. If you can not answer all three…

A: The term, Orthogonal, describes the relationship of the axis of the ½” NPT pipe plug with the main…

Q: Hello, thank you for your feedback but unfortunately your result does not coincide with the problem…

A:

Q: ead intrustions on example and help anwser it please and th

A: Jsolid Cylinder =πd432 DAC = 0.9 JAC =π 0.9432=0.064412467

Q: Design engineers in many situations must justify their selection of beams and pin-ended columns used…

A:

Q: Hii, I asked this question but may I ask how to get 1.1547? thank you

A: In this problem, it is asking how to get 1.1547 in the given calculations.

Q: AN 8mm DIAMETER STEEL ROD, 20m LONG SUPPORTS A JOKN WEIGHT. FIND THE MAXIMUM. TENSILE STRESS H THE…

A: Unit weight of steel,  γ=77 kN/m3 So total weight will be due to 10kN and self-weight combined. So,…

Q: Q 13. A frame is said to be 'Perfect frame, if it followS certain relation betvoen number of members…

A: Perfect frame will not change when it is subjected to load with help of perfect number of members…

Q: How did you get the temperature 367? What is the solution?

A:

Q: Sketch the free-body diagram of the cylinder.

A:

Q: A hydraulic punch press is capable of delivering 2,000kPa pressure on its platen from its 250mm…

A: Given: A hydraulic punch press is capable of delivering 2,000kPa pressure on its platen from its…

Q: Make an illustration for this problem and label it completely. This lever has a fulcrum that they…

A:

Chemical and Phase Equilibrium

Phase diagrams or equilibrium phase diagrams are the graphical representations that show the phase transformations of the constituting elements with respect to the pressure, temperature, and compositions. The diagrams show the conditions that limit the different phases, namely solid, liquid, and gas. The diagram can also be utilized to verify the relations between the state variables. Most of the phase diagrams are temperature-pressure phase diagrams, with the variable parameter as the composition. Usually other variables such as solubility and pressure parameters are not indicated in the phase diagram. For a one-component system (unary phase diagram), the phase diagram is generally a function of temperature and pressure as the state variables, or temperature and volume. However, for a binary system (two-phase) having two components, the phase diagram is a function of temperature and composition as the state variables only. Coexisting of the different phases of the constituting elements is indicated in the phase diagram. A ternary phase diagram can be characterized by consisting of three phases in equilibrium.